| Other CCNA Interview Questions |
| |
| Question | Asked @ | Answers |
| |
| What is convergence time?
A.) The update time
B.) The time it takes to reload a router
C.) The time it takes for a packet to reach its destination
D.) The time is takes for all routers update their tables
after a change
takes place | | 1 |
| What are the 2 functions of the Data Link Mac layer?
A.) Handles access to shared media
B.) Manages protocol access to the physical network medium
C.) Provides SAPs for higher level protocols
D.) Allows multiple devices to uniquely identify one another
on the data
link layer | | 1 |
| What is Spanning Tree Protocol and how it work? I know it
is - STP is Spanning tree Protocol. It Stops the looping in
the network? How STP work? How it stop Looping in network? | | 2 |
| You have typed "ping" 172.16.101.1 and get the following
display:
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echoes to 172.16.101.1,
timeout is 2 seconds:
.!!!!
What does the "." signify?
A. That one message timed out.
B. That all messages were successful.
C. That one message was successful.
D. That one message completed in under the allotted
timeframe. | | 1 |
| All equipment located at the customers site is called:
A.) CPE
B.) CO
C.) DCE
D.) Demarc
E.) DTE | | 1 |
| What command can you type to view the connections after
telneting
into multiple routers simultaneously?
A.) sh users
B.) sh ports
C.) sh host
D.) sh sessions | | 1 |
| Which three basic switch functions increase available
bandwidth on the networks? (Choose three)
A. loop avoidance
B. address learning
C. hop count limiting
D. broadcast filtering
E. packet forward/filtering | | 3 |
| what is the high order bit in class a
1
11
110
10
mine answer 1 | | 2 |
| what are layer hierarchy of cisco | | 1 |
| Which of the following are valid Cisco encapsulation type names?
A.) arpa = IPX Ethernet
B.) novell-ether = IPX Ethernet_802.3
C.) snap = IEEE 802.2 SNAP on Ethernet, FDDI, and Token Ring
D.) novell-fddi = IPX Fddi_Raw
E.) sap = IEEE 802.2 on Ethernet, FDDI, and Token Ring
F.) hdlc = HDLC on serial interfaces | | 1 |
| Two of the protocols that can be carried in the Protocol
field of an IP packet are?
A. TCP
B. UDP
C. FTP
D. TFTP | | 2 |
| What is difference between Store-and-Forward, cut-through,
Fragment-Free Method? | Microsoft | 2 |
| What is the purpose of Split Horizon?
A.) It prevents the regular update messages from reinstating
a route that
has gone down
B.) Information received on an interface cannot be sent back
out the same
interface
C.) Informs all neighbor routers that two routes exist
D.) Tells the router the destination is unreachable | | 1 |
| what is the diffination of bandwidth. | | 1 |
| Choose three reasons why the networking industry uses a layered
model:
A.) It facilitates systematic troubleshooting
B.) It allows changes in one layer to occur without changing
other layers
C.) It allows changes to occur in all layers when changing
one protocol
D.) It clarifies how to do it rather than what general
function to be done
E.) It clarifies what general function is to be done rather
than how to
do it | | 1 |
| Identify the protocol to test connectivity without
configuring any
layer 3
protocols?
A.) TCP
B.) Ping
C.) IP
D.) CDP
E.) Telnet | | 1 |
| Which two steps are part of the process of creating Frame
Relay subinterfaces on a point to point connection? (Choose
two)
A. configure the router to forward all broadcast packets
B. remove any network address assigned to the physical interface
C. configure the local data link connection identifier
(DICI) for the subinterfaces
D. cartoon the total committed information rate (CIP)
available among the subinterfaces | | 1 |
| Identify the command that displays the SAP table?
A.) show ipx servers
B.) display SAP table
C.) display SAP's
D.) show sap table | | 1 |
| What type of frame does CDP use to gather information about it's
neighbors?
A.) TCP/IP
B.) Novell-ether
C.) Subnetwork Access Protocol (SNAP)
D.) Ethernet_II | | 1 |
| How do you disable advanced editing?
A.) terminal editing
B.) terminal no editing
C.) disable editing
D.) no terminal editing | | 2 |
| |
| For more CCNA Interview Questions Click Here |
Site Map
