| Other CCNA Interview Questions |
| |
| Question | Asked @ | Answers |
| |
| Identify the 3 methods routers learn paths to destinations?
A.) Dynamic routing
B.) None of the above, configured by default
C.) Default routes
D.) Administrative distance
E.) Static routes | | 1 |
| Given the global configuration commands:
'banner motd #'
'Hello #'
When would the message be displayed?
A.) The message of the day banner shows up before login.
B.) The message of the day banner shows up during logoff.
C.) These commands are not the right syntax for MOTD.
D.) Message of the day banners are displayed upon entering
global config
mode.
E.) Message of the day banners are not possible.
F.) The message of the day would be, 'Hello #' | | 1 |
| Using the TCP/IP protocol suite, a message is sent from host
A to a destination IP address on the same LAN. How does
host A determine the destination of a MAC address?
A. It uses a proxy APP
B. It uses APP requests
C. It uses PARP requests
D. It uses a router lookup table | | 1 |
| Identify 3 IP routing protocols?
A.) RIP
B.) AURP
C.) OSPF
D.) IGRP
E.) ARP
F.) ICMP | | 2 |
| What is ISR or NonISR router? Difference between ISR or
NonISR router? | HCL | 3 |
| Which two statements about integrated services digital
network (ISDN) are true?
A. ISDN provides data only capability
B. ISDN provides an integrated voice/data capability
C. The ISDN standards define the hardware and call setup
schemes for end the end digital connectivity
D. Users receive more bandwidth on WANS with a leased lin of
56 Cops than with multiple B channels | | 1 |
| Hi, I have packet tracer 5.0. I want to test intervlan
routing routing. Can someone plz tell me about intervlan
routing? | | 1 |
| What is the 5-4-3-2-1 rule of network design? | | 3 |
| How do you disable advanced editing?
A.) terminal editing
B.) terminal no editing
C.) disable editing
D.) no terminal editing | | 2 |
| What not a name of an ISP?
A. MSN
B. Comcast
C. Verizon
D. McDonalds | | 1 |
| Whith the hierarchical numbering of IP addressing what
determines the spoon of the address that will identify the
network number?
A. subnet mask
B. dots between octets
C. class of the first octet
D. assignments of DHCP
E. address resolution process | | 1 |
| What is the protocol number for UDP?
A.) 6
B.) 17
C.) 25
D.) 21 | | 1 |
| In IOS boot sequence if the flash is erased, and there is
no access to TFTP server, and we can't load the partial IOS
from ROM. Is there any possiblity that we can still boot
the router/switch from external PC in which the IOS is
installed? | | 5 |
| Of the following switching types, which one has the lowest
latency?
A.) Cut-through
B.) Fragment Free
C.) None
D.) Store-and-forward | | 1 |
| In order to configure a Frame Relay subinterface with IP
identify
the 2 commands that must be configured on the physcial
interface?
A.) Router(config-if)# encapsulation frame-relay
B.) Router(config-if)# no ip address
C.) Router(config-if)#encapsulation subinterface frame-relay
D.) Router(config)# subinterface s0 encapsulation frame-relay | | 2 |
| You are given the following address: 153.50.6.27/25.
Determine the subnet mask, address class, subnet address,
and broadcast address.
A. 255.255.255.128, B,153.50.6.0, 153.50.6.127
B. 255.255.255.128, C,153.50.6.0, 153.50.6.127
C. 255.255.255.128, C,153.50.6.127, 153.50.6.0
D. 255.255.255.224, C,153.50.6.0, 153.50.6.127 | | 1 |
| Which three of the following are true statements about
connection-oriented
sessions?
A.) The segments delivered are acknowledged back to the
sender upon
their reception
B.) Any segments not acknowledged are retransmitted by the
receiver
C.) A manageable data flow is maintained in order to avoid
congestion,
overloading and loss of any data
D.) Segments are sequenced back into their proper order upon
arrival at
their destination | | 3 |
| What is the default LMI type?
A.) Cisco
B.) ANSI
C.) IETF
D.) Q933a | | 2 |
| Which statement about half duplex Ethernet operations is true?
A. With half duplex transmission frames feed into a single
cable in one direction at a time.
B. Half duplex transmission between stations is achieved by
using point to point Ethernet and Fast Ethernet connections
C. Half duplex transmission between stations is achieved by
using point to munificent Ethernet and Fast Ethernet connections
D. Half duplex Ethernet technology provides a transmit
circuit connection wired directly to the receiver circuit at
the other end of the connection | | 5 |
| What is required to support full-duplex Ethernet?
A.) Multiple paths between multiple stations on a link
B.) Automatic sensing operation by all connected stations
C.) Loopback and collision detection disabled
D.) Full-duplex NIC cards | | 1 |
| |
| For more CCNA Interview Questions Click Here |
Site Map
