| Other CCNA Interview Questions |
| |
| Question | Asked @ | Answers |
| |
| Station A is transmitting data to station B, and expects an
acknowledgment
after every 400 bytes. After transmitting data for a while,
the two
stations determine the line is reliable and change to
expecting and
acknowledgement every 600 bytes.
This is an example of (pick the best answer only):
A.) BECN
B.) Sliding Windows
C.) Poison Reverse
D.) Countdown timers
E.) Split Horizon
F.) Count to infinity | | 1 |
| Which ISDN specification deals with call Setup and Teardown?
A.) Q-Series
B.) J-Series
C.) I- Series
D.) C- Series
E.) F-Series | | 1 |
| What does a metric of 16 hops represent when using RIP?
A.) Number of hops to the destination
B.) Destination unreachable
C.) Number of routers
D.) Bandwidth | | 3 |
| Which three basic switch functions increase available
bandwidth on the networks? (Choose three)
A. loop avoidance
B. address learning
C. hop count limiting
D. broadcast filtering
E. packet forward/filtering
F. broadcast packet hop count learning/forward/filtering | | 1 |
| You are a system administrator and you want to deny access to a
group of computers with addresses 172.30.16.0 to
172.30.31.0. Which
wildcard mask would you use?
A. 0.0.15.255
B. 0.0.255.255
C. 0.0.31.255
D. 0.0.127.255
E. 0.0.255.255 | | 1 |
| In regards to the OSI seven-layer model, at which layer is
EBCDIC
and ASCII?
A.) Presentation
B.) Application
C.) Transport
D.) Session
E.) Datalink
F.) Network | | 1 |
| Identify the command to configure the router to boot from an IOS
located on a TFTP server?
A.) boot system tftp IOS.exe 172.16.5.1
B.) boot system tftp 172.16.5.1 IOS.exe
C.) boot system flash tftp 172.16.5.1
D.) boot system IOS.exe 172.16.5.1 | | 1 |
| What is the default LMI type for Cisco Routers that are using
Frame-Relay?
A.) Annex D
B.) Q933A
C.) Cisco
D.) IETF
E.) ARPA
F.) Anex A | | 2 |
| What type of Ethernet operation allows only one entity to
transmit
at a time? For example, if someone else is transmitting,
they must wait.
A.) Full-Duplex
B.) Dual-Duplex
C.) Half-Duplex
D.) Latex
E.) Quarter-Duplex
F.) Suplex | | 1 |
| Which two does 100BaseT use?
A.) CSMA/CD
B.) IEEE 802.5
C.) 802.3u
D.) Switching with 53-byte cells | | 3 |
| Which statement about the data link connection identifier
(DLCI) is true?
A. It is a number that identifies a local virtual circuit in
a Frame Relay network
B. It is a signaling standard between the CIDE device and
the Frame Relay switch
C. It is the clock speed (pod speed) of the connection
(local loop) to the Frame Relay Cloud
D. It is the Maximum number of uncommitted bits that the
Frame Relay switch will attempt to transfer beyond the
Committed Information Rate (CIP) | | 2 |
| Hi Jitendera, I need ur suggestion. I completed my CCNA
certification & also hving some sort of real time
experience. Now i m planning to do CCNP. Little bit
confusion is that whether it wud be better for me to go for
CCNP ya CCNA (Security). As off my goal is to reach CCIE
(Security & Switching/Routing). So tell me some solution of
my confusion yaar..!!!
Thanx & Regards
Shahin.. | | 1 |
| what is the binary value of loop back address | | 11 |
| Assuming no subnetting, which two pieces of information can
be derived from the IP address 144.132.25.10? (Choose two)
A. It is a Class C address
B. It is a Class B address
C. The network address is 144.0.0.0
D. The network address is 144.132.25.0
E. The host spoon of the address is 25.10 | | 2 |
| Which three are typical operational phases in a basic
connection oriented network service?
A. call setup
B. data transfer
C. load balancing
D. call termination
E. caller ID
F. call prionflication
G. data segmentation
H. data and momma
I. data link identification
J. callering book | | 1 |
| What are the two components of an IPX address?
A. network number IP address
B. MAC address node number
C. network number MAC address
D. network number arched number | | 1 |
| A server is running HTTP, SMTP and DHCP. Which of the
following best explains how the server is able to handle
all three services over the same connection?
The server has separate buffer areas for each
application and forwards all data to each service. If the
data does not apply to that application, it is discarded.
The server processes each packet one at a time and
forwards the data to the application that indicates that it
is waiting for a transmission to arrive. The data is
discarded if it does not apply to that application.
The server uses the destination port number in the
TCP/UDP header to identify the service. The data is
forwarded to the service identified by the port number.
The server uses separate three-way handshake connections
to control the flow of the data and relates the service to
the proper connection. This relationship allows the server
to pass the data to the proper service.
| | 1 |
| As a system administrator, you perform an extended ping at
the privileged EXEC prompt. As part of the display, you see
"Set DF bit in IP header? [yes] :" What would happen if you
answered no at the prompt.
A. This lets the router fragment the packet.
B. It tells the router not to fragment the packet.
C. This lets the router direct the packet to the destination
it finds in its routing table.
D. It tell the router to send the packet to the next hop
router. | | 1 |
| Which of the following will show an extended access list 150?
A.) sh access-list
B.) sh ip int
C.) sh ip access-list 150
D.) sh access-list 150 extended | | 1 |
| What is the default bandwidth of a serial connection?
A.) 1200 baud
B.) 1.544 Mbps (T1)
C.) 10 Mbps
D.) 96Kpbs | | 3 |
| |
| For more CCNA Interview Questions Click Here |
Did you received any Funny E-Mails from your Friends and like to share with rest of our friends? Yeah!! you can post that stuff 
Site Map
