| Other CCNA Interview Questions |
| |
| Question | Asked @ | Answers |
| |
| which of the following address represent unicast address
A 224.1.5.2
B ffff.ffff.ffff.ffff
C 192.168.24.59/30
D 255.255.255.255
E 172.138.128.255
plz tell what should be answer plz tell with explanation
| IPsoft | 3 |
| What does the IPX maximum path command do?
A.) Allows you to disable the TTL on an IPX packet
B.) This parameter is only used in NLSP routing
C.) Sets the maximum metric that can appear in the routing table
D.) Configures round robin load sharing over multiple equal
metric paths
(parallel paths) | | 1 |
| A user device that connects to a DCE must be which of the
following?
A.) DTE
B.) CPE
C.) Demarc
D.) DCE
E.) CO | | 1 |
| Which command line option will determine what traffic is
interesting enough to establish a dialup connection?
A.) dialer map
B.) dialer string
C.) dialer in-band
D.) dialer-list
E.) dialer negotiation | | 1 |
| Identify 3 Fast Ethernet technologies?
A.) 100 Base FastEther
B.) 100 Base FX
C.) 100 Base T4
D.) 100 Base TX | | 1 |
| What command would show the version of the IOS that you are
running?
A.) show nvram
B.) show version
C.) show startup-config
D.) show ios
E.) ver -a
F.) show ram | | 1 |
| There is a process in Frame-Relay where LMI resolves an IP
address
from a DLCI number. What is this called?
A.) arp
B.) inverse arp
C.) rarp
D.) automap
E.) reverse arp
F.) arp | | 1 |
| Which three tasks are required to confound a dial on demand
routing (DDR) Basic Rate Interface (BRI) connection?
(Choose three)
A. define static routes
B. confound the abler information
C. specify the interesting franc that can enable the link
D. define a DDR password to exchange when the link comes up | | 1 |
| Which command displays all the commands in the history buffer?
A. CTRL H
B. show buffer
C. show history
D. show history buffer | | 2 |
| Identify the 2 commands that will display the status and
information about interface E0 only?
A.) show interface ethernet E0
B.) show interface E0
C.) show E0
D.) show int E0
E.) show interface | | 1 |
| Identify the command to display the hardware platform
information?
A.) show all
B.) show platform
C.) display hardware
D.) show version | | 1 |
| Identify the command that displays ethernet0/1 interface status?
A.) show interface ethernet0/1
B.) show interface ethernet e0/1
C.) show interface ethernet0.1
D.) show ethernet0/1 | | 1 |
| Which of the following will apply IPX sap access list 1010 for
incoming traffic, assume you are at the interface configuration?
A.) ipx input-sap-filter 1010 in
B.) ipx input-sap-filter 1010
C.) ipx access-group 1010 in
D.) ipx access-list 1010 in | | 1 |
| My question is how windows pc will act as a router?
Jitendra understand this question? I again want to ask you
is it possibele for windows pc to act like a router | | 2 |
| What is the purpose of the DLCI?
A.) Identifies the remote routers
B.) Contained with a 802.2 frame for routing purposes
C.) Used with PPP during authentication
D.) Identifies the PVC in a Frame Relay network | | 1 |
| Which command line statement determines the number of seconds a
dialup connection can wait without any traffic before the
router hangs up?
A.) dialler max-time
B.) dialler timeout
C.) dialer idle-timeout
D.) dialer hang-up
E.) disconnect-timer | | 2 |
| Given the Novell IPX address 1aceb0b.0000.0c12.3456 which
part is
the network portion of the address?
A.) 0000
B.) 1
C.) 3456
D.) 1ace
E.) 0000.0c12.3456
F.) 1aceb0b | | 2 |
| Identify the following command to configure a secret password to
'cisco'?
A.) Router(config)#enable password cisco secret
B.) Router(config)#enable secret cisco
C.) Router(config)#enable secret password cisco
D.) Router(config)#set secret = cisco | | 1 |
| What is Cisco's default encapsulation method on serial
interfaces?
A.) ANSI
B.) Cisco
C.) Q933a
D.) HDLC | | 2 |
| Which of the following is a characteristic of a switch, but
not of
a repeater?
A.) Switches forward packets based on the IPX or IP address
in the frame
B.) Switches forward packets based on the IP address in the
frame
C.) Switches forward packets based on the MAC address in the
frame
D.) Switches forward packets based only on the IP address in
the packet | | 2 |
| |
| For more CCNA Interview Questions Click Here |
Site Map
