| Other CCNA Interview Questions |
| |
| Question | Asked @ | Answers |
| |
| Which statements are true regarding half duplex?
A.) Only works in a point-to-point configuration
B.) Allows for transmitting and receiving but not at the
same time
C.) Allow for transmitting and receiving of data simultaneously
D.) Doubles the bandwidth | | 1 |
| Where is the point between the customers site and the phone
carrier that responsibility changes?
A.) CO
B.) Demarc
C.) DCE
D.) DTE
E.) CPE | | 1 |
| What is BGP attribute & How many types of attributes are
used by BGP??? | Hathway | 3 |
| Identify the 2 commands that display the clock rate
configured on
the serial0 interface?
A.) show serial0
B.) show interface serial0
C.) show clock rate serial 0
D.) show controllers serial 0
E.) show running-config | | 2 |
| thnx Jitender singh...as u told to install a stp in switches
and problem vil b get solved...i wanna kno how to install
stp in switches??
plz tel me detailled steps...
thanx for ur answer. | | 1 |
| What is the protocol number for TCP?
A.) 80
B.) 21
C.) 11
D.) 6 | | 1 |
| Identify the 2 commands that display the clock rate
configured on
the serial0 interface?
A.) show serial0
B.) show interface serial0
C.) Show clock rate serial 0
D.) show controllers serial 0
E.) show running-config | | 1 |
| Identify the 2 items that TCP and UDP share in common?
A.) Both use port numbers to identify upper level applications
B.) Operate at the Network layer
C.) Both are Transport protocols
D.) Both are reliable communications | | 1 |
| Which layer is responsible for coordinating communication
between
systems?
A.) Application
B.) Network
C.) Session
D.) Transport
E.) Physical
F.) Data Link | | 1 |
| Why Authentication Header (AH) is not compatible with the
network that using NAT??????
Jitu, looking for u specially...!!!! U knw why i m looking
for u..!!! | | 1 |
| What is the default bandwidth of a serial connection?
A.) 1200 baud
B.) 1.544 Mbps (T1)
C.) 10 Mbps
D.) 96Kpbs | | 3 |
| A router on one side of a PPP link uses the resonance RTR1
and the password COPP1-PWD. Which configuration line on
RTR1 enables a connection between RTR1 and another router
named RTR2?
A. username, RTR2 password COPR1-PWD,
B. username, RTR1 password COPR1-PWD,
C. username, RTR2 password COPR2-PWD,
D. username, RTR1 password COPR2-PWD, | | 1 |
| What is the standard ISDN term for a non-native analog
telephone?
A.) TE1
B.) TA
C.) LE
D.) TE2
E.) ET | | 1 |
| Which command assigns the login password CISCO on the
console terminal line?
A. line vty 0 login password cisco
B. line console login password cisco
C. line login terminal password cisco
D. line console 0 login
E. line console 0 login password cisco | | 2 |
| Which layer is responsible for providing mechanisms for
multiplexing
upper-layer application, session establishment, and tear
down of virtual
circuits?
A.) Session
B.) Network
C.) Physical
D.) Transport
E.) Application
F.) Presentation | | 1 |
| What is the default interval for SAP updates?
A.) 60 seconds
B.) 15 seconds
C.) 30 seconds
D.) 120 seconds | | 1 |
| What is the purpose of ARP?
A.) IP to host name resolution
B.) Host name to IP address resolution
C.) Mac to IP address resolution
D.) IP to Mac address resolution | | 2 |
| Which commands would assign and enable IPX on an interface ?
A.) enable netware
B.) enable novell-ether
C.) router#(config)ipx routing
D.) You must first enable IPX globally and then
assign the network number to the interface .
E.) enable ipx
F.) router#(config-if)ipx network 4a | | 1 |
| Identify the command to configure a description on an interface?
A.) Router> description Finance department
B.) Router(config)# description Finance department
C.) Router(config-if)# description Finance department
D.) Router# description Finance department | | 1 |
| An ISDN BRI circuit can be described as which of the following?
A.) 3B channels
B.) 2-64Kbps B channels and 1-16Kbps D channel
C.) none of the above
D.) 2-64Kbps B channels and 1-16Kbps C channel | | 1 |
| |
| For more CCNA Interview Questions Click Here |
Site Map
