| Other CCNA Interview Questions |
| |
| Question | Asked @ | Answers |
| |
| What parameter is used with statically assigned routers to tell
packets which interface to use to reach a distant network?
A.) Mask
B.) Subnet
C.) Default gateway
D.) Interface | | 1 |
| Which statement about half duplex Ethernet operations is true?
A. With half duplex transmission frames feed into a single
cable in one direction at a time.
B. Half duplex transmission between stations is achieved by
using point to point Ethernet and Fast Ethernet connections
C. Half duplex transmission between stations is achieved by
using point to munificent Ethernet and Fast Ethernet connections
D. Half duplex Ethernet technology provides a transmit
circuit connection wired directly to the receiver circuit at
the other end of the connection | | 5 |
| What does a metric of 16 hops represent when using RIP?
A.) Number of hops to the destination
B.) Destination unreachable
C.) Number of routers
D.) Bandwidth | IBM | 2 |
| A ISDN PRI circuit can be described as which of the following?
A.) 24 B channels and 1-64Kbps D channel
B.) 23 B channels and 1-64Kbps D channel
C.) 2-D channels and 1-C channel
D.) 2-64Kbps B channels and 1-16Kbps D channel | | 1 |
| Which OSI Reference Layer controls application to application
communication?
A.) Datalink
B.) Network
C.) Transport
D.) Session
E.) Physical | | 1 |
| Which command should you use to create an IP standard access
list?
A. access-list standard 172.16.4.13
B. access-list 1 deny 172.16.4.13 0.0.0.0
C. access-list 100 deny 172.16.4.13 0.0.0.0
D. access-list 198 deny 172.16.4.13 255.255.255.255 | | 2 |
| Which OSI layer establishes, maintains and terminates sessions
between
applications?
A.) Application
B.) Physical
C.) Data-Link
D.) Presentation
E.) Network
F.) Session | | 1 |
| What is VLSM? how to Calculate VLSM? where it is use and
why? | | 4 |
| What is a characteristic of Store and Forward switches?
A.) They work at wire speed.
B.) They are the same as Cut-Through switching in 'prune' mode.
C.) They forward based on transport layer info.
D.) They forward the frame before it is completely read.
E.) They increase latency. | | 1 |
| Identify the command to determine if CDP is enabled?
A.) show enable cdp
B.) show cdp enabled
C.) show cdp run
D.) show cdp | | 2 |
| What are the 2 functions of the Data Link Mac layer?
A.) Handles access to shared media
B.) Manages protocol access to the physical network medium
C.) Provides SAPs for higher level protocols
D.) Allows multiple devices to uniquely identify one another
on the data
link layer | | 1 |
| What do the following commands accomplish?
access-list 1 deny 172.16.4.0 0.0.0.255
access-list 1 permit any
interface ethernet 0
IP access-group 1 out
A. This will block traffic from subnet 172.16.4.0 and allow
all other
traffic.
B. This will allow traffic from subnet 172.16.4.0 and block
all other
traffic.
C. All traffic is allowed.
D. All traffic is blocked. | | 1 |
| Which three tasks are required to confound a dial on demand
routing (DDR) Basic Rate Interface (BRI) connection?
(Choose three)
A. define static routes
B. confound the abler information
C. specify the interesting franc that can enable the link
D. define a DDR password to exchange when the link comes up | | 1 |
| The maximum distance on a 10BaseT network from the hub to a
workstation is which of the following?
A.) 500 meters
B.) 1000 meters
C.) 100 meters
D.) 1500 meters | | 2 |
| can we measure how much a host exact bandwidth using by a
network cable which is communicating over the network?
options: 1- via Router 2- Switch, 3- other device... if
yes.. then how ( with every option) | | 3 |
| Choose the following that are benefits to segmenting with
router:
A.) Flow Control
B.) Manageability
C.) Multiple Active Paths
D.) Explicit packet lifetime control | | 1 |
| Identify the access-list range for an extended IP access-list?
A.) 800 - 899
B.) 1 - 99
C.) 1000 - 1099
D.) 100 - 199 | | 4 |
| Which of the following are valid WAN terms?
A.) DTE
B.) DCE
C.) Demarc
D.) CPE | | 1 |
| Identify the 2 commands the saves the running-config to NVRAM?
A.) write memory
B.) copy running-config startup-config
C.) write network
D.) write backup | | 1 |
| If configuring a Cisco router to connect to a non-Cisco router
across a
Frame Relay network, which encapsulation type would you select?
A.) Q933a
B.) ISDN
C.) IETF
D.) CISCO
E.) ANSI | | 1 |
| |
| For more CCNA Interview Questions Click Here |
Site Map
