| Other CCNA Interview Questions |
| |
| Question | Asked @ | Answers |
| |
| Which of the following is a layer 2 device?
A.) Switch
B.) Router
C.) Repeater
D.) Hub | | 3 |
| Identify the order of the 5 step encapsulation?
1) Create the segment
2) Convert the frame to bits
3) Create the packet
4) Create the frame
5) User creates the data
A.) 1,2,4,2,5
B.) 2,1,3,4,5
C.) 5,1,3,4,2
D.) 5,3,4,1,2 | | 1 |
| Which command loads a new version of the Cisco IOS into a
router?
A. copy flash ftp
B. copy ftp flash
C. copy flash tftp
D. copy tftp flash | | 1 |
| Identify the command to display the configured IP routing
protocols?
A.) show protocols
B.) show protocols all
C.) show routing-protocols
D.) show ip protocols | | 2 |
| Which 2 commands shows the Cisco IOS filename?
A.) show IOS
B.) show ver
C.) show flash
D.) show mem
E.) show NVRAM | | 1 |
| Which of the following are characteristics of UDP?
A.) UDP is connection oriented.
B.) UDP is used with TFTP.
C.) UDP is unreliable.
D.) UDP is connectionless.
E.) UDP is at the transport layer.
F.) UDP uses no acknowledgements. | | 4 |
| What are two functions of the ICMP protocol? (Choose two)
A. to map IP addresses to Ethernet addresses
B. to map common names to network addresses
C. to forward SNMP alerts to management consoles
D. to generate an echo reply in response to a ping test
E. to send a host or pod unreachable message from a router
to the source of an undeliverable packet | | 1 |
| Identify 3 characteristics of an IP address?
A.) Contains a network portion and a host portion
B.) 32 bits long
C.) Unique to each network
D.) Part of the default Cisco configuration
E.) Referred to as the hardware address | Infosys | 3 |
| X.25 is characterized by layer 2 identifiers, and what else?
A.) Virtual Lan's
B.) Session Layer
C.) Transport Layer
D.) Routing Updates
E.) PVC's | | 1 |
| What command can be used to test IPX connectivity?
A.) Ping 2e.000.0045.8923
B.) Ping 192.168.100.1
C.) Ping ipx 2e.0000.0045.8923
D.) Ipx ping 2e.0000.0045.8923 | | 1 |
| Which of the following provide connection-oriented transport
to upper
layer protocols?
A.) SPX
B.) RIP
C.) NLSP
D.) NCP | | 1 |
| Identify the command that configures serial0 for PPP
encapsulation?
A.) Router(config)# encapsulation ppp
B.) Router(config-if)# encapsulation serial ppp
C.) Router(config-if)# encapsulation ppp
D.) Router# encapsulation ppp | | 1 |
| Identify 3 characteristics of the Network layer (OSI layer 3)?
A.) Connnection oriented
B.) Path determination
C.) Supports multiplexing
D.) Manages sessions
E.) Packet forwarding | | 1 |
| The administrator of a comapny needs to ensure that a web
server in
their network is accessible from the Internet. Since the
network uses private
addressing, this requires an IP-to-registered-address
mapping. The following
command is entered on the router:
router(config)# ip nat inside source static 192.168.2.1
198.18.1.254
After unsuccessful results from a ping to the Internet, the
administrator issues the
show ip nat translations command and the output is blank.
What could be the
problem with the NAT configuration for this mapping?
A. The keyword overload is missing from the command.
B. The administrator needs to define a NAT pool first.
C. An access list must be defined to create static NAT
translations.
D. The interfaces need to be configured for NAT. | | 4 |
| Which statement about the Point to Point Protocol (PPP) is true?
A. PPP supports TCP/IP but not Novell IPX
B. PPP is being phased out of existence by the Serial Line
Internet Protocol (SLIP)
C. PPP providces router to router and host to network
connections over both synchronous and asynchronous circuits
D. PPP is an ITU T and ANSI standard that defines the
process for sending data over a packet switched data network
(PSDN) | | 1 |
| Identify 2 HDLC characteristics?
A.) Default serial encapsulation
B.) Open standard
C.) Supports Stacker compression
D.) Supports point-to-point and multipoint | | 1 |
| What are the OSPF router rules???? | NIIT | 6 |
| Cisco routers use wildcard masking to identify how to check or
ignore corresponding IP address bits. What does setting a
wildcard mask
bit to 0 cause the router to do?
A. It tells the router to check the corresponding bit value.
B. It tells the router to ignore the corresponding bit value.
C. It tells the router to check its alternate routing list.
D. It tells the router to use its primary routing list. | | 1 |
| At what layer of the OSI reference model does FRAME-RELAY
map to?
A.) Session
B.) Physical
C.) Network
D.) Presentation
E.) Transport
F.) Datalink | | 1 |
| Identify the command to configure the router for IGRP autonomous
system 100?
A.) Router(config)# router igrp 100
B.) Router> router igrp 100
C.) Router# router igrp 100
D.) Router(config)# router igrp | | 3 |
| |
| For more CCNA Interview Questions Click Here |
Did you received any Funny E-Mails from your Friends and like to share with rest of our friends? Yeah!! you can post that stuff 
Site Map
