| Other CCNA Interview Questions |
| |
| Question | Asked @ | Answers |
| |
| Identify 1 characteristic of RARP?
A.) MAC to IP address translation
B.) Connectionless delivery of packets
C.) Can be used to initiate remote O/S load sequence
D.) Generates error and control messages | | 3 |
| There is a process in Frame-Relay where LMI resolves an IP
address
from a DLCI number. What is this called?
A.) arp
B.) inverse arp
C.) rarp
D.) automap
E.) reverse arp
F.) arp | | 1 |
| Select the compression protocols for PPP?
A. Stac
B. Predictor
C. Quality
D. Magic Number | | 1 |
| How does a switch use store and forward?
A.) By using a Class I repeater in a collision domain
B.) The LAN switch copies the entire frame into its onboard
buffers and
then looks up the destination address in its forwarding, or
switching,
table and determines the outgoing interface
C.) By using broadcast addresses as source addresses
D.) The switch waits only for the header to be received
before it checks
the destination address and starts forwarding the packets | | 1 |
| Which OSI layer handles physical address, network topology?
A.) Presentation
B.) Physical
C.) Transport
D.) Application
E.) Data-Link
F.) Network | | 1 |
| Identify 3 characteristics of a connection oriented protocol?
A.) Path determination
B.) Flow control
C.) Acknowledgements
D.) Uses hop count as metric
E.) 3 step handshake | | 2 |
| Where is the backup configuration file stored?
A.) RAM
B.) ROM
C.) Console
D.) NVRAM | | 1 |
| What are the job opportunities i will get once i complete
my CCNA certification. | | 2 |
| Identify the default values that make up IGRP's composite
metric?
A.) Bandwidth
B.) Load
C.) Reliability
D.) MTU
E.) Delay | | 1 |
| Which of the following will apply IPX sap access list 1010 for
incoming traffic, assume you are at the interface configuration?
A.) ipx input-sap-filter 1010 in
B.) ipx input-sap-filter 1010
C.) ipx access-group 1010 in
D.) ipx access-list 1010 in | | 1 |
| Hi, All
I am configuring EIGRP in Packet tracer, after configuring
all the things it is not working but in one condition it is
working fine if i am putting all my router and network
withing one network subnets e.g. 172.16.0.0 or 10.0.0.0 but
whenever i am puting different network subnets e.g. in one
network it is RA(config-if)#=ip address 10.0.0.1, and in
fa0/0= 192.168.1.10 and in RB(config-if)#10.0.0.2 (s1/0) and
in S1/1 11.0.0.1 and in fa 0/0 192.168.100.1 ,where as in
third router RC(config-if)#=ip address 11.0.0.2 and in fa
0/0 172.16.1.10 and after configuring all this serial is
showing up and protocol showing up but eigrp process not
taking place after adding eigrp configuration, i tried with
"no auto-summary" command but not working.. Suggest me where
i missing something? can mail me at : gtech.innovator@gmail.com | | 18 |
| What is a characteristic of Store and Forward switches?
A.) They forward the frame before it is completely read.
B.) They work at wire speed.
C.) They are the same a Cut-Through switching.
D.) They read the entire frame and check CRC before forwarding.
E.) They decrease latency. | | 1 |
| Identify the statement which connects access-list 101 inbound to
interface e0?
A.) Router(config-if)# ip access-group 101 in
B.) Router(config-if)# ip access-group 101
C.) Router(config)# ip access-group 101 e0 in
D.) Router(config)# ip access-group 101 e0 in | | 1 |
| Given the following static route command, 'ip route 3.3.3.0
255.255.255.0
4.4.4.4 125', which portion represents the administrative
distance?
A.) 3.3.3.0
B.) 255.255.255.0
C.) 4.4.4.4
D.) route
E.) 125 | | 2 |
| In order to configure a Frame Relay subinterface with IP
identify
the 2 commands that must be configured on the physical
interface?
A.) Router(config-if)# encapsulation frame-relay
B.) Router(config-if)# no ip address
C.) Router(config-if)#encapsulation subinterface frame-relay
D.) Router(config)# subinterface s0 encapsulation frame-relay | | 1 |
| what is burst rate | ASD-Lab | 1 |
| Identify the command to display the configured IP routing
protocols?
A.) show protocols
B.) show protocols all
C.) show routing-protocols
D.) show ip protocols | | 1 |
| The ICMP (referred to in PFC 1700) is implemented by all
TCP/IP hosts
A. true
B. false | | 1 |
| What is the standard ISDN term for a native ISDN telephone?
A.) ET
B.) TE1
C.) TE2
D.) LE
E.) TA | | 1 |
| What is an administrative distance of 0 mean?
A.) 0 means unbelievable
B.) 0 is for EIGRP
C.) 0 is the default distance for directly connected networks
D.) 0 means unreachable | | 1 |
| |
| For more CCNA Interview Questions Click Here |
Did you received any Funny E-Mails from your Friends and like to share with rest of our friends? Yeah!! you can post that stuff 
Site Map
