| Other CCNA Interview Questions |
| |
| Question | Asked @ | Answers |
| |
| Identify the command to disable CDP on an interface?
A.) Router(config-if)# no cdp enable
B.) Router(config-if)# no cdp run
C.) Router# no cdp enable
D.) Router(config-if)# no cdp | | 1 |
| In order to limit the quantity of numbers that a system
administrator has to enter, Cisco can use which abbreviation
to indicate
0.0.0.0?
A. host
B. any
C. all
D. include | | 1 |
| Which symbol in the router prompt indicates you are in the
privelaged mode?
A. >
B. !
C. #
D. : | | 3 |
| Which of the following is an example of the Network Layer?
A.) TCP
B.) IP
C.) SQL
D.) Token Ring
E.) LLC | | 2 |
| What does the command show access-lists 101 list?
A. all defended access lists
B. all access lists within the router
C. the contents of standard access list 101
D. the contents of defended access list 101 | | 1 |
| What is the UDP datagram format?
A. Source Port - 16 bits, Destination Port - 16 bits, Length
- 16 Bits, Checksum - 16 bits, Data
B. Destination Port - 16 bits, Source Port - 16 bits, Length
- 16 Bits, Checksum - 16 bits, Data
C. Source Port - 16 bits, Destination Port - 16 bits,
Checksum - 16 Bits, Length - 16 bits, Data
D. Source Port - 8 bits, Destination Port - 8 bits, Length -8
Bits, Checksum - 8 bits, Data | | 1 |
| Which of the following describe SMTP?
A.) Used for downloading files to the router.
B.) Used for sending e-mail.
C.) Uses TCP.
D.) Uses UDP.
E.) Uses port 25.
F.) Used for managing IP devices. | | 1 |
| Which statement is true regarding the user exec and privileged
exec mode?
A.) The '?' only works in Privileged exec
B.) Privileged exec is a subset of the user exec mode
C.) They both require the enable password
D.) User exec is a subset of the privileged exec mode | | 1 |
| A default route is analogous to a _________.
A. default gateway
B. static route
C. dynamic route
D. one-way route | | 1 |
| Dear Mr.Shahin thank you very much for your advise i realy
thanks full to you.
Best of luck | | 2 |
| The following is partial output from a routing table ;
'192.168.10.0 [100/1300] via 10.1.0.1, 00:00:23, Ethernet1'
Which routing protocol is being used? (assuming defaults
have not been
changed)
A.) OSPF
B.) RIP
C.) BGP
D.) IGRP | | 1 |
| what are two security appliances that can be installed a
network | | 7 |
| Identify the following command to configure a secret password to
'cisco'?
A.) Router(config)#enable password cisco secret
B.) Router(config)#enable secret cisco
C.) Router(config)#enable secret password cisco
D.) Router(config)#set secret = cisco | | 1 |
| Which three statements about Frame Relay configurations
using subinterfaces is true? (Choose three)
A. Each subinterface is conferred either multipoint or point
to point
B. Any network address must be removed from the physical
interface
C. The configuration of subinterfaces is done in router
(config-if)# mode
D. Frame Relay encapsulation must be conferred on each
subinterface | | 1 |
| Which of the following are characteristics of UDP?
A.) UDP is connection oriented.
B.) UDP is used with TFTP.
C.) UDP is unreliable.
D.) UDP is connectionless.
E.) UDP is at the transport layer.
F.) UDP uses no acknowledgements. | | 4 |
| In the setup dialog, what do the square brackets indicate?
A. current or default spores
B. hard coded values that cannot be modified
C. values entered by the administrator but not saved
D. values that must be written to PAVRAM before becoming enabled | | 1 |
| Which OSI layer establishes, maintains and terminates sessions
between hosts?
A.) Application
B.) Physical
C.) Data-Link
D.) Presentation
E.) Network
F.) Session | | 1 |
| Which command specifies a second subinterface on serial
interface 0?
A. interface s 0.2 point-to-point
B. interface 2 s.0 point-to-point
C. suberinterface 2.s 0 point-to-point
D. interface s 0 sub 2 point-to-point
E. interface s 0.1 point-to-point sub 2 | | 1 |
| Identify the default values that make up IGRP's composite
metric?
A.) Bandwidth
B.) Load
C.) Reliability
D.) MTU
E.) Delay | | 1 |
| Which three tasks are required to confound a dial on demand
routing (DDR) Basic Rate Interface (BRI) connection?
(Choose three)
A. define static routes
B. confound the abler information
C. specify the interesting franc that can enable the link
D. define a DDR password to exchange when the link comes up | | 1 |
| |
| For more CCNA Interview Questions Click Here |
To Refer this Site to Your Friends 
Site Map
