ALLInterview.com :: Home Page KalAajKal.com
 Advertise your Business Here     
Browse  |   Placement Papers  |   Company  |   Code Snippets  |   Certifications  |   Visa Questions
Post Question  |   Post Answer  |   My Panel  |   Search  |   Articles  |   Topics  |   ERRORS new
   Refer this Site  Refer This Site to Your Friends  Site Map  Bookmark this Site  Set it as your HomePage  Contact Us     Login  |  Sign Up                      
info       Did you received any Funny E-Mails from your Friends and like to share with rest of our friends? Yeah!! you can post that stuff   HERE
Google
 
Categories  >>  Certifications  >>  Cisco Certifications  >>  CCNA
 
 


 

 
 CCNA interview questions  CCNA Interview Questions
 CCDA interview questions  CCDA Interview Questions
Question
Which ISDN specification deals with call Setup and Teardown?

A.) Q-Series

B.) J-Series

C.) I- Series

D.) C- Series

E.) F-Series
 Question Submitted By :: Guest
I also faced this Question!!     Rank Answer Posted By  
 
  Re: Which ISDN specification deals with call Setup and Teardown? A.) Q-Series B.) J-Series C.) I- Series D.) C- Series E.) F-Series
Answer
# 1
Answer: A

The 2 most important ISDN specifications are Q & I:

Q = Call setup and teardown.

I = Concepts and terminology.
 
Is This Answer Correct ?    0 Yes 0 No
Guest
 

 
 
 
Other CCNA Interview Questions
 
  Question Asked @ Answers
 
Identify the hardware component that stores the bootstrap program? A.) ROM B.) NVRAM C.) Booter load D.) RAM E.) Flash  2
Identify 2 features of X.25? A.) Supports only IP B.) Utilizes switched and permanent virtual circuits C.) Contains minimal flow control and error recovery D.) Utilizes LAPB as it's data-link protocol  1
what is the difference between a passive and active hub?? which is better ??  5
Identify the components in the following command 'interface serial0/1/1' A.) Serial interface, port number 0, slot 1, port adapter 1 B.) Serial interface, slot 1, port number 1, port adapter 0 C.) Serial interface, slot 0, port adapter 1, port number 1  2
Identify the command to run 'setup'? A.) Router(config)#setup B.) Router?setup C.) Router#setup D.) Router>setup  1
Identify 3 Fast Ethernet technologies? A.) 100 Base FastEther B.) 100 Base FX C.) 100 Base T4 D.) 100 Base TX  1
How many Frame-relay encapsulation types are available with Cisco routers? A.) Four B.) Two C.) Five D.) Three  1
'Show cdp neighbors detail' show the following 3 pieces of information? A.) Hardware platform B.) Software version C.) Same as 'show version' command D.) Up to 1 address for each protocol E.) Non-direct connected routers  2
Which routing protocols uses connection-oriented routing updates? A.) IGRP B.) UDP C.) RIP D.) IP E.) BGP  2
Identify the command to display the status of the Frame Relay virtual circuit? A.) Router# show frame-relay virtual-circuit B.) Router(config)# show frame-relay pvc C.) Router# show frame-relay pvc D.) Router# show virtual  1
How can an Ethernet switch improve network performance? Choose three  1
What's the default CDP holdtime in seconds for Cisco routers? A.) 30 seconds B.) 180 seconds C.) 90 seconds D.) 60 seconds  3
thnx jitender...its me shridh...m working for SG ltd..the situation iz like ths -at a specific time in our company the internet connectivity goes off...v hav two networks in our company...but out of it only one link goes down for 5-10 sec...a fastethernet port becomes down for few sec and automatically becomes Up... Is this occures becoz of Power?? If yes thn y the 2nd network is not affected?? plz tel me jitender how to resolve ths problem? as u sd loop in switch is the primary cause of ths....i wanna know how to resolve it...thnx for ur replys jitender sinha.  2
Which command will enable debugging for IPX RIP updates? A.) debug ipx B.) debug ipx rip C.) debug ipx rip activity D.) debug rip E.) debug ipx packets  1
Novell NetWare has an Ethernet frame type called Ethernet_II. What is the matching Cisco command line keyword for this encapsulation method? A.) dix B.) sap C.) arpa D.) gns E.) snap F.) novell-ether  1
The PDU at the network layer is a ________ Packet Frame Segment Bit  3
Identify the following command to configure a secret password to 'cisco'? A.) Router(config)#enable password cisco secret B.) Router(config)#enable secret cisco C.) Router(config)#enable secret password cisco D.) Router(config)#set secret = cisco  1
Identify 2 functions of IPX access-lists? A.) Control SAP traffic B.) Limit number of Novell servers on a network C.) Limit number of workstations on a network D.) Block IPX traffic  1
'Show cdp neighbors detail' show the following 3 pieces of information? A.) Hardware platform B.) Software version C.) Same as 'show version' command D.) Up to 1 address for each protocol E.) Non-direct connected routers  1
What is the UDP datagram format? A. Source Port - 16 bits, Destination Port - 16 bits, Length - 16 Bits, Checksum - 16 bits, Data B. Destination Port - 16 bits, Source Port - 16 bits, Length - 16 Bits, Checksum - 16 bits, Data C. Source Port - 16 bits, Destination Port - 16 bits, Checksum - 16 Bits, Length - 16 bits, Data D. Source Port - 8 bits, Destination Port - 8 bits, Length -8 Bits, Checksum - 8 bits, Data  1
 
For more CCNA Interview Questions Click Here 
 
 
 
 
 
   
Copyright Policy  |  Terms of Service  |  Help  |  Site Map 1  |  Articles  |  Site Map  |   Site Map  |  Contact Us interview questions urls   External Links 
   
Copyright © 2007  ALLInterview.com.  All Rights Reserved.

ALLInterview.com   ::  Forum9.com   ::  KalAajKal.com