When setting up a frame-relay network between a Cisco router and a non-

Advertise your Business Here

Refer this Site

Login | Sign Up


	Ask Questions on ANYTHING, that arise in your Daily Life at FORUM9.COM

Categories >> Certifications >> Cisco Certifications >> CCNA

CCNA Interview Questions

CCDA Interview Questions

Question

When setting up a frame-relay network between a Cisco router
and a

non-Cisco router, what encapsulation type should you use?

A.) SAP

B.) CISCO

C.) IANA

D.) Apollo

E.) IETF

F.) Q933A

Question Submitted By :: Guest

I also faced this Question!!

Rank

Answer Posted By

Re: When setting up a frame-relay network between a Cisco router and a non-Cisco router, what encapsulation type should you use? A.) SAP B.) CISCO C.) IANA D.) Apollo E.) IETF F.) Q933A

Answer
# 1

Answer: E

The Internet Engineering Task Force (IETF) encapsulation
method is the

standard encapsulation type for Frame Relay. Cisco routers
default to

the CISCO encapsulation method, because it was created
before there was

a standard.

Is This Answer Correct ?

1 Yes

0 No

Guest

Question	Asked @	Answers
Other CCNA Interview Questions


There is a process in Frame-Relay where LMI resolves an IP address from a DLCI number. What is this called? A.) arp B.) inverse arp C.) rarp D.) automap E.) reverse arp F.) arp		1
what is vlan and how will you configure vlan on 3650 switch and how many valn can you create on that switch	Volvo	3
How do you view the routers current processor utilization? A.) show version B.) show processes cpu C.) show running-config D.) show startup-config E.) show cpu F.) show utilization	Cisco	2
Which of the following do not belong to the customer? A.) CO B.) DCE C.) Router D.) CPE E.) Demarc F.) DTE		1
Which statement is true regarding full duplex? A.) Allows for transmission and receiving of data simultaneously B.) Only works in a multipoint configuration C.) Does not affect the bandwidth D.) Allows for transmission and receiving of data but not at the same time		1
You are a system administrator and you want to deny access to a group of computers with addresses 172.30.16.0 to 172.30.31.0. Which wildcard mask would you use? A. 0.0.15.255 B. 0.0.255.255 C. 0.0.31.255 D. 0.0.127.255 E. 0.0.255.255		1
Hello Mr.Jitendera Kuamr Sinha, how is every thing going on? Thanks for your reply. Dear Friend if you can Explain it little bit deeper i will be realy thanks full. Wish you all the Best.		1
Which statement about Ethernet networks is true? A. The advantage of a full duplex is the ability to transmit data over 111 cable B. Full duplex Ethernet requires a point-to-point connection when only two nodes are present C. Ethernet switches can use full duplex mode to connect multiple nodes to a single pod of a switch D. Half duplex is a cut through packet processing method that is vow fast little error correction Full duplex is a store and forward method that is slower but has better error correction		1
Identify the protocol to test connectivity without configuring any layer 3 protocols? A.) TCP B.) Ping C.) IP D.) CDP E.) Telnet		1
Using the TCP/IP protocol suite a message is sent from host A to a destination IP address on the same LAN. How does host A determine the destination of MAC address? A. It uses a proxy APP B. It uses APP requests C. It uses RARP requests D. It uses a router lookup table		1
Can anyone explain the Split Horizon rule in RIP & also Split Horizon with Poison reverse. Jitu.... U knw wat i expect.. hehehehehe...		1
Layer 1 and Layer 2 devices must forward a broadcast. Which of the following devices fall into this category? Gateway Switch Router All of the above.		1
Describe End to End network services: (Choose all that apply) A.) Best Route selection B.) Accomplished Segment by Segment, each segment is autonomous C.) Flow Control & Data Integrity D.) Best efforts packet delivery		1
Which type of switching is considered to be 'wire speed?' A.) Cut-Through B.) Multiplexed C.) Inverted D.) Layer 4 E.) Store and Forward F.) Layer 3		1
What does the Spanning Tree Algorithm (STA) do? A.) Restore lost frames B.) Builds routing tables for routing through an internetwork C.) Forward packets through a switch D.) STA is implemented by STP to prevent loops		1
What are two ways IPX supports multiple logical networks on an individual underrate? (Choose two) A. network number B. routing protocol C. encapsulation type D. autonomous system number		1
What are the job opportunities i will get once i complete my CCNA certification.		2
Which command listed below sets the banner message when someone connects to the router? A.) message # B.) banner # C.) login banner # D.) description # E.) login description # F.) banner motd #		1
The default routing protocol for IPX is IPX RIP. How do you view the routing updates sent and received by the router? A.) debug ipx routing B.) debug ipx routing activity C.) debug rip D.) show ipx routing E.) sh ipx F.) debug ipx rip		2
Identify 3 methods used to prevent routing loops? A.) Split horizon B.) Holddown timers C.) Poison reverse D.) SPF algorithm E.) LSP's		2

For more CCNA Interview Questions Click Here


Copyright Policy \| Terms of Service \| Help \| Site Map 1 \| Articles \| Site Map \| Site Map \| Contact Us \|

Copyright © 2007 ALLInterview.com. All Rights Reserved.

ALLInterview.com :: Forum9.com :: KalAajKal.com