When determining whether or not to route a LAN segment, which rule of t

Advertise your Business Here

Refer this Site

Login | Sign Up


	To Refer this Site to Your Friends Click Here

Categories >> Certifications >> Cisco Certifications >> CCNA

CCNA Interview Questions

CCDA Interview Questions

Question

When determining whether or not to route a LAN segment,
which rule

of thumb do you use?

A.) 60/40

B.) 50/50

C.) 80/20

D.) 90/10

E.) 70/30

Question Submitted By :: Guest

I also faced this Question!!

Rank

Answer Posted By

Re: When determining whether or not to route a LAN segment, which rule of thumb do you use? A.) 60/40 B.) 50/50 C.) 80/20 D.) 90/10 E.) 70/30

Answer
# 1

Answer: E

The industry standard rule is 80/20, which means 80% local,
20% over the

router.

However, according to Cisco's online documentation, the
answer is 70/30.

This makes sense, considering more and more traffic is
starting to go

from the desktop to an ultimate destination outside the
local are

network, such as the Internet.

Is This Answer Correct ?

0 Yes

0 No

Guest

Question	Asked @	Answers
Other CCNA Interview Questions


What must be true for two Routers running IGRP to communicate their routes? A.) Same autonomous system number B.) Connected using Ethernet only C.) Use composite metric D)Configured for PPP	Allied-Group	1
Identify the length of an IPX address and it's components? A.) 80 bits, 48 bits network and 32 bits node B.) 32 bits, 16 bits network and 16 bits node C.) None of the above D.) 80 bits, 32 bits network and 48 bits node		1
Which OSI layer provides best effort end to end packet delivery? A.) Data-Link B.) Presentation C.) Network D.) Transport E.) Physical F.) Application		1
What does a metric of 16 hops represent when using RIP? A.) Number of hops to the destination B.) Destination unreachable C.) Number of routers D.) Bandwidth		3
How does the cut-through switching technique work? A.) By using broadcast address as source addresses B.) The switch waits only for the header to be received before it checks the destination address and starts forwarding the packets C.) The LAN switch copies the entire frame into its onboard buffers and then looks up the destination address in its forwarding, or switching, table and determines the outgoing interface D.) By using a Class I repeater in a collision domain		3
The Datalink layer works with which of the following: A.) Packets B.) Bits C.) Globules D.) Frames E.) Segments		2
Which command loads a new version of the Cisco IOS into a router? A. copy flash ftp B. copy ftp flash C. copy flash tftp D. copy tftp flash		1
Which of the following are valid WAN terms? A.) DTE B.) DCE C.) Demarc D.) CPE		2
Which command displays all the commands in the history buffer? A. CTRL H B. show buffer C. show history D. show history buffer		2
What is the standard ISDN term for a non-native analog telephone? A.) TE1 B.) TA C.) LE D.) TE2 E.) ET		1
The Network layer works with which of the following: A.) Globules B.) Bits C.) Packets D.) Segments E.) Frames		2
You have powered on a new router and you want to create an initial configuration. Which mode should you use? A. copy mode B. user mode C. setup mode D. startup mode	Enrich	3
What does the trace response !H mean? * A: Network unreachable * B: Not forwarded due to ACL restriction * C: Protocol unreachable * D: Port could not be reached		2
IGRP supports a feature that allows traffic to be distributed among up to 6 (4 default) paths to provide greater overall throughput and reliability. What is this called? A. unequal-cost load balancing B. equal-cost load balancing C. proportionate load balancing D. low cost load balancing		1
PLACE YOURS QUESTION HERE I ALSWYS BE HERE FROM 9 AM TO 6PM SO U CAN FIND YOUR ANSWER QUICKLY.IF I KNOW THEN ? JJIITTEENNDDEERRAA SSIINNHHAA		4
Which range of possible numbers do standard ipx access lists have? A. 100 199 B. 600 699 C. 800 899 D. 1000-1099		1
Identify the 3 key features of the Cisco Discovery Protocol? A.) Off by default B.) Will allow for the discovery of layer 3 addresses on neighbor routers C.) Verifies connectivity D.) Open standard E.) Does not require any layer 3 protocols to be configured		1
thnx Jitender singh...as u told to install a stp in switches and problem vil b get solved...i wanna kno how to install stp in switches?? plz tel me detailled steps... thanx for ur answer.		1
Identify 3 characteristics regarding IP access-lists? A.) Can be configured as a standard access-list B.) Can be run from another router running IP C.) Can be configured as a named access-list D.) Are the same as IPX access-lists E.) Can be configured as an extended access-list		1
What is a benefit of a virtual LAN (VLAN)? A. It increases the number of broadcast domains B. It decreases the number of broadcast domains C. It increases the numberr of collision domains D. It decreases the number of collision domains E. Since it is a vitual Interface it never shuts down		3

For more CCNA Interview Questions Click Here


Copyright Policy \| Terms of Service \| Help \| Site Map 1 \| Articles \| Site Map \| Site Map \| Contact Us \|

Copyright © 2007 ALLInterview.com. All Rights Reserved.

ALLInterview.com :: Forum9.com :: KalAajKal.com