| Other CCNA Interview Questions |
| |
| Question | Asked @ | Answers |
| |
| Identify the command to configure the router to boot from an
alternate IOS located in flash?
A.) boot system flash IOS.exe
B.) boot system tftp IOS.exe 172.16.5.1
C.) boot system alternate IOS.exe
D.) boot system rom IOS.exe | | 1 |
| Which two statements about integrated services digital
network (ISDN) are true?
A. ISDN provides data only capability
B. ISDN provides an integrated voice/data capability
C. The ISDN standards define the hardware and call setup
schemes for end the end digital connectivity
D. Users receive more bandwidth on WANS with a leased lin of
56 Cops than with multiple B channels | | 1 |
| What is an administrative distance of 0 mean?
A.) 0 means unbelievable
B.) 0 is for EIGRP
C.) 0 is the default distance for directly connected networks
D.) 0 means unreachable | | 2 |
| Which layer defines bit synchronization?
A.) Application
B.) Network
C.) Transport
D.) Physical
E.) Session
F.) Session | | 1 |
| Identify the switching method that receives the entire frame
then
dispatches it?
A.) Cut-through
B.) Receive and forward
C.) Store and forward
D.) Fast forward | | 1 |
| What is LSA? How many types of LSA used by OSPF version 2?? | Hathway | 2 |
| Which ISDN protocol prefix specifies switching and signaling?
A.) I
B.) E
C.) Q
D.) S | | 1 |
| What is required to support full-duplex Ethernet?
A.) Multiple paths between multiple stations on a link
B.) Automatic sensing operation by all connected stations
C.) Loopback and collision detection disabled
D.) Full-duplex NIC cards | | 1 |
| Identify the command that will display the RIP routes
entering and
leaving the router?
A.) Router(config)# debug ip rip
B.) Router# debug ip rip
C.) Router>debug ip rip
D.) Router# debug rip routes | | 1 |
| Hello every one. Please can any one explain me the
difference b/w Cisco Switch/ws-c3560-24ps-s and Switch/ws-
c3560-24ts-s. what is does PS & TS Stands for. Waiting for
your passtive reply. Wish You all the best | | 2 |
| What does the ping response & mean?
* A: unreachable
* B: congestion
* C: user interrupt
* D: unknown packet type
* E: lifetime exceeded
| | 2 |
| Which three protocols are correctly matched to their
transport layer functions? (Choose three)
A. route selection IP
B. sliding window UDP
C. well known pods IP
D. route validation ICMP
E. connection oriented TCP
F. three-way handshake TCP
G. no sequence and acknowledgement UDP | | 1 |
| What is the bandwidth capacity of one ISDN B channel
A. 64 kbps
B. 128 kbps
C. 512 kbps
D. 1.54 mkbps | | 3 |
| IP RIP routing is conferred on a router but not all
interfaces attach to RIP networks. What should you use to
prevent all RIP routing updates from being sent through
selecedc interfaces without using access lists?
A. passive route
B. default routes
C. passive interface
D. route update filtering | | 2 |
| Identify the 2 rules used when configuring a Distance Vector
routing
protocol?
A.) Physically connected network(s)
B.) Configure the classfull address, no subnets
C.) Enable CDP so neighbors can be detected
D.) Same autonomous network | | 1 |
| Identify the 2 rules used when configuring a Distance Vector
routing protocol?
A.) Physically connected network(s)
B.) Configure the classful address, no subnets
C.) Enable CDP so neighbors can be detected
D.) Configure all networks in Area0 | | 1 |
| What are the two most common transport layer protocols?
UDP
TCP
IPX
ARP
| | 2 |
| Identify the command that configures serial0 for PPP
encapsulation?
A.) Router(config)# encapsulation ppp
B.) Router(config-if)# encapsulation serial ppp
C.) Router(config-if)# encapsulation ppp
D.) Router# encapsulation ppp | | 1 |
| What command would you use to find out the names of Novell
servers on a network?
A. show ipx servers
B. show ipx hosts
C. show ipx sap
D. show ipx nodes. | | 1 |
| Identify 2 transport layer protocols?
A.) IP
B.) TCP
C.) CDP
D.) ARP
E.) UDP | | 1 |
| |
| For more CCNA Interview Questions Click Here |
Site Map
