| Other CCNA Interview Questions |
| |
| Question | Asked @ | Answers |
| |
| what are loops in switches excactly...and how does it gets
created??? | | 1 |
| Hi Gyes, here is new question. can you provide answer of
following question
Like linux, can we windows as router?
If yes how can we able to do this, | | 2 |
| How does a switch use store and forward?
A.) By using a Class I repeater in a collision domain
B.) The LAN switch copies the entire frame into its onboard
buffers and
then looks up the destination address in its forwarding, or
switching,
table and determines the outgoing interface
C.) By using broadcast addresses as source addresses
D.) The switch waits only for the header to be received
before it checks
the destination address and starts forwarding the packets | | 1 |
| Which of the following will apply IPX sap access list 1010 for
incoming traffic, assume you are at the interface configuration?
A.) ipx input-sap-filter 1010 in
B.) ipx input-sap-filter 1010
C.) ipx access-group 1010 in
D.) ipx access-list 1010 in | | 1 |
| Which statements are true regarding half duplex?
A.) Only works in a point-to-point configuration
B.) Allows for transmitting and receiving but not at the
same time
C.) Allow for transmitting and receiving of data simultaneously
D.) Doubles the bandwidth | | 1 |
| The Datalink Layer is broken down into 2 layers, LLC and
MAC. The
LLC establishes media independence and what else?
A.) Provides Windowing.
B.) Provides flow control.
C.) Provides SAP's (Service Access Points).
D.) The Datalink layer does not have sublayers.
E.) Provides SAP's (Service Advertising Protocol).
F.) RIP Updates. | | 1 |
| Which layer is responsible for flow control,
acknowledgement, and
windowing?
A.) Transport
B.) Network
C.) Application
D.) Session
E.) Physical
F.) Data Link | | 2 |
| The Datalink layer works with which of the following:
A.) Packets
B.) Bits
C.) Globules
D.) Frames
E.) Segments | | 1 |
| What is the default CDP broadcast update rate for Cisco routers?
A.) 120 seconds
B.) 60 seconds
C.) 30 seconds
D.) 90 seconds | | 1 |
| what is frame relay.and how it is different from isdn | HCL | 1 |
| You are a system administrator and you want to deny access to a
group of computers with addresses 172.30.16.0 to
172.30.31.0. Which
wildcard mask would you use?
A. 0.0.15.255
B. 0.0.255.255
C. 0.0.31.255
D. 0.0.127.255
E. 0.0.255.255 | | 1 |
| What is the maximum number of subnets that can be assigned
to networks when using the address 172.16.0.0 with a subnet
mask of 255.255.240.0? (Assume older version UNIX
workstations are in use.)
A. 16
B. 32
C. 30
D. 14
E. It is an invalid subnet mask for the Network. | | 1 |
| CSMA/CD stand for which of the following?
A.) Carrier Sense, Multiple Access with Collision Detection
B.) Collision Sense, Multiple Access with Collision Detection
C.) Collision Sense, Multiple Access with Carrier Detection
D.) Carrier Sense, MAC address with Collision Detection | | 1 |
| Which protocol will send a message to routers if a network
outage or
congestion occurs?
A.) ARP
B.) TCP
C.) IP
D.) ICMP | | 1 |
| What is the Difference between Hub and Switch? | | 2 |
| Your network is having IP problems connecting to one or more
Frame Relay peer routers. Which two commmands should you
use to show the routers that are reachable? (Choose two)
A. show ip map
B. show ip router
C. show frame-relay map
D. debug frame-relay map | | 1 |
| When discussing static routes, what is the gateway parameter
used
for?
A.) Determining the dynamic route
B.) Defining the subnet
C.) Defining the Administrative Distance
D.) Determining the next hop | | 1 |
| in which way the datas will transfer from one host to
another host by using osi layer? | | 2 |
| Which protocol will send a message to routers if a network
outage
or congestion occurs?
A.) ARP
B.) TCP
C.) IP
D.) ICMP | | 1 |
| Which OSI layer supports the communication component of an
application?
A.) Data-Link
B.) Physical
C.) Session
D.) Presentation
E.) Application
F.) Transport | | 2 |
| |
| For more CCNA Interview Questions Click Here |
Site Map
