| Other CCNA Interview Questions |
| |
| Question | Asked @ | Answers |
| |
| Identify 2 PPP characteristics?
A.) Is proprietary to Cisco
B.) Supports authentication
C.) Support compression
D.) Run on a multi-access network | | 2 |
| Although Cisco IOS 11.2 and later can auto-detect the LMI
type in
Frame Relay, which command will force the LMI type to q933a?
A.) frame-relay lmi-type q933a
B.) encapsulation frame-relay q933a
C.) don't need to, it is the default
D.) encapsulation q933a
E.) encapsulation frame-relay type=q933a | | 1 |
| At what layer of the OSI reference model does FRAME-RELAY
map to?
A.) Session
B.) Physical
C.) Network
D.) Presentation
E.) Transport
F.) Datalink | | 1 |
| Which of the following are logged when IP access list logging is
enabled?
A.) source address
B.) protocol
C.) source port
D.) destination address
E.) access list number
F.) destination port | | 1 |
| What are the 2 functions of the Data Link Mac layer?
A.) Handles access to shared media
B.) Manages protocol access to the physical network medium
C.) Provides SAPs for higher level protocols
D.) Allows multiple devices to uniquely identify one another
on the data
link layer | | 1 |
| Your Ethernet interface currently has the IP address of
1.1.1.1/24. You would like it to have a second IP address of
2.2.2.2/24.
Which command will do that?
A.) ip address 1.1.1.1 2.2.2.2 255.255.255.0
B.) ip address 2.2.2.2 255.255.255.0 secondary
C.) ip address 2.2.2.2 255.255.255.0
D.) This cannot be done, you can only have 1 IP address per
physical
interface.
E.) ip address 2.2.2.2 /24 | | 1 |
| What is proxy-ARP and how it is used and configured | | 1 |
| Identify the command to configure the router for IGRP autonomous
system 100?
A.) Router(config)# router igrp 100
B.) Router> router igrp 100
C.) Router# router igrp 100
D.) Router(config)# router igrp | CMS | 2 |
| Which of the following are Transport layer protocols?
A.) UDP
B.) TCP
C.) NBP
D.) IP
E.) SPX | | 1 |
| How often does IP RIP send out routing table updates by default?
A.) They send complete updates every 30 seconds
B.) They send partial updates every 30 seconds
C.) They send complete updates every 60 seconds
D.) They send partial updates every 60 seconds | | 2 |
| What does the Spanning Tree Algorithm (STA) do?
A.) Restore lost frames
B.) Builds routing tables for routing through an internetwork
C.) Forward packets through a switch
D.) STA is implemented by STP to prevent loops | | 1 |
| what is ip address and what is the difference between the ip
address and mac address why we are not using mac address instead of ip address | IBM | 3 |
| Identify the 3 pieces of hardware you would not install to
prevent
broadcasts?
A.) Switch
B.) Repeater
C.) Bridge
D.) Router | | 2 |
| What are hold-downs used for?
A.) To prevent regular update messages from reinstating a
route that has
come back up
B.) Information received on an interface cannot be sent back
out the same
interface
C.) To prevent regular update messages from reinstating a
route that has
gone down
D.) To hold the routing table from being sent to another router | | 1 |
| Identify the hardware component used to store buffers, tables,
running-configuration etc?
A.) NVRAM
B.) ROM
C.) RAM
D.) Flash | | 1 |
| Which command loads a new version of the Cisco IOS into a
router?
A. copy flash ftp
B. copy ftp flash
C. copy flash tftp
D. copy tftp flash | | 1 |
| Which of the following will show an extended access list 150?
A.) sh access-list
B.) sh ip int
C.) sh ip access-list 150
D.) sh access-list 150 extended | | 1 |
| Identify the statement which connects access-list 101 inbound to
interface e0?
A.) Router(config-if)# ip access-group 101 in
B.) Router(config-if)# ip access-group 101
C.) Router(config)# ip access-group 101 e0 in
D.) Router(config)# ip access-group 101 e0 in | | 1 |
| A default route is analogous to a _________.
A. default gateway
B. static route
C. dynamic route
D. one-way route | | 1 |
| what is 5-4-3 rule? | | 1 |
| |
| For more CCNA Interview Questions Click Here |