| Other CCNA Interview Questions |
| |
| Question | Asked @ | Answers |
| |
| Which of the following provide connection-oriented transport to
upper layer protocols?
A.) SPX
B.) RIP
C.) NLSP
D.) NCP | | 1 |
| Which protocol gets a hardware address from a known IP address?
A.) RARP
B.) TCP
C.) IP
D.) BootP
E.) ARP
F.) ICMP | | 3 |
| The following selections show the command prompt and the
configuration of the IP network mask. Which two are
correct?
A. Router#term IP netmask-format { bitcount | decimal |
hexadecimal }
B. Router(config-if)#IP netmask-format { bitcount | decimal
| hexadecimal }
C. Router(config-if)#netmask-format { bitcount | decimal |
hexadecimal }
D. Router#ip netmask-format { bitcount | decimal | hexadecimal } | | 1 |
| Identify the OSI layer which is responsible for end-to-end
connections?
A.) Network
B.) Transport
C.) Session
D.) Data link
E.) TCP | | 1 |
| What command would show the version of the IOS that you are
running?
A.) show nvram
B.) show version
C.) show startup-config
D.) show ios
E.) ver -a
F.) show ram | | 1 |
| What is the regional Telco office called, where the customers
local loop
terminates?
A.) Demarc
B.) DTE
C.) DCE
D.) CO
E.) CPE | | 1 |
| What command would you use to find out the names of Novell
servers on a network?
A. show ipx servers
B. show ipx hosts
C. show ipx sap
D. show ipx nodes. | | 1 |
| Identify the switching method that receives the entire frame
then
dispatches it?
A.) Cut-through
B.) Receive and forward
C.) Store and forward
D.) Fast forward | | 1 |
| Identify the type of hardware required to connect a Token ring
network to
an Ethernet network?
A.) Repeater
B.) TR-Enet
C.) Router
D.) Token Ring to Ethernet translation hub | | 1 |
| The "ipx delay number" command will allow an administrator to
change the default settings. What are the default settings?
A. For LAN interfaces, one tick; for WAN interfaces, six
ticks
B. For LAN interfaces, six ticks; for WAN interfaces, one
tick
C. For LAN interfaces, zero ticks; for WAN interfaces, five
ticks
D. For LAN interfaces, five ticks; for WAN interfaces, zero
Ticks | | 1 |
| Which layer hides details of network dependent information from
the higher layers by providing transparent data transfer?
A.) Transport
B.) Physical
C.) Data Link
D.) Session
E.) Application
F.) Network | | 1 |
| Which of the following is true regarding standard ISDN BRI
service?
A.) ISDN BRI B channels are typically 64K.
B.) ISDN BRI can handle only voice.
C.) ISDN BRI can handle only data.
D.) ISDN BRI has 2B and 1D channels.
E.) ISDN BRI D channels are 16K.
F.) ISDN BRI can handle voice and data. | | 1 |
| Which command would you type to show SAP and RIP updates you are
receiving on an interface?
A.) sh ipx servers
B.) sh ipx traffic
C.) sh ipx interface
D.) sh ipx route | | 1 |
| To monitor ipx traffic on a network, what command would you use?
A. debug ipx transaction
B. show ipx traffic
C. show ipx events
D. display ipx traffic | | 2 |
| Identify 3 UDP characteristics?
A.) Reliable communication protocol
B.) Applications that use UDP must incorporate reliability
C.) Connection-less oriented
D.) Incorporates no handshaking | | 2 |
| A network is vow congested currently all the devices are
connected through a hub. Which would best decrease
congestion on this network?
A. add a second hub
B. replace the hub with a router
C. replace the hub with a switch
D. replace the hub with a repeater | | 1 |
| What is the default interval for SAP updates?
A.) 60 seconds
B.) 15 seconds
C.) 30 seconds
D.) 120 seconds | | 1 |
| what is meant by domain ?
what is mean by DNS? | | 9 |
| What's the default CDP holdtime in seconds for Cisco routers?
A.) 30 seconds
B.) 180 seconds
C.) 90 seconds
D.) 60 seconds | | 3 |
| Which of the following is a layer 2 device?
A.) Switch
B.) Router
C.) Repeater
D.) Hub | | 3 |
| |
| For more CCNA Interview Questions Click Here |
Did you received any Funny E-Mails from your Friends and like to share with rest of our friends? Yeah!! you can post that stuff 
Site Map
