| Other CCNA Interview Questions |
| |
| Question | Asked @ | Answers |
| |
| Which feature of PPP (Point to Point Protocol) allows the router
to bind multiple channels together, to form a single logical
channel?
A.) multi-link ppp
B.) multi-channel ppp
C.) can't be done
D.) omni-ppp
E.) plp | | 1 |
| Where is the point between the customers site and the phone
carrier that responsibility changes?
A.) CO
B.) Demarc
C.) DCE
D.) DTE
E.) CPE | | 1 |
| Identify 3 UDP characteristics?
A.) Reliable communication protocol
B.) Applications that use UDP must incorporate reliability
C.) Connnection-less oriented
D.) Incorporates no handshaking | | 2 |
| Which statement about Ethernet networks is true?
A. The advantage of a full duplex is the ability to transmit
data over 111 cable
B. Full duplex Ethernet requires a point-to-point connection
when only two nodes are present
C. Ethernet switches can use full duplex mode to connect
multiple nodes to a single pod of a switch
D. Half duplex is a cut through packet processing method
that is vow fast little error correction Full duplex is a
store and forward method that is slower but has better error
correction | | 1 |
| What is Cisco register bits? How they help? | jetking | 1 |
| What is the routing algorithm used by RIP and IGRP?
A.) OSPF
B.) Link-state
C.) Dynamic
D.) Distance Vector | Cisco | 2 |
| Identify IPX SAP and it's purpose?
A.) Sonet Access Pipe - interface to Sonet ring
B.) Service Advertising Protocol - advertise services
C.) Server Appletalk Protocol - appletalk directory services
D.) Service Access Point - identify upper layer protocols | | 1 |
| Identify the command that specifies Serial 0 in slot 1?
A.) Router(config)# interface serial1/1
B.) Router(config)# interface serial1/0
C.) Router(config)# interface serial0.1
D.) Router(config)# interface serial0/1 | | 1 |
| All equipment located at the customers site is called:
A.) CPE
B.) CO
C.) DCE
D.) Demarc
E.) DTE | | 1 |
| Which of the following are solutions to the problems encountered
with Distance-Vector routing?
A.) Defining a Maximum
B.) Poison Reverse
C.) Triggered Updates
D.) Shortest path first algorithm.
E.) Split Horizon | | 1 |
| In regards to TCP/IP, which class of address allows for the
fewest
valid
Internet hosts?
A.) D
B.) E
C.) Classes are not used in TCP/IP.
D.) B
E.) C
F.) A | | 1 |
| Which of the following protocols are used for logical network
addressing?
A.) IP
B.) TCP
C.) ARP
D.) ICMP
E.) RARP
F.) BootP | | 1 |
| Identify the command to reload the router?
A.) Router(config)# reload
B.) Router# reset
C.) Router# reload
D.) Router> reload | | 1 |
| In order to configure a Frame Relay subinterface with IP
identify
the 2 commands that must be configured on the physical
interface?
A.) Router(config-if)# encapsulation frame-relay
B.) Router(config-if)# no ip address
C.) Router(config-if)#encapsulation subinterface frame-relay
D.) Router(config)# subinterface s0 encapsulation frame-relay | | 1 |
| What does the Spanning Tree Algorithm (STA) do?
A.) Restore lost frames
B.) Builds routing tables for routing through an internetwork
C.) Forward packets through a switch
D.) STA is implemented by STP to prevent loops | | 1 |
| What three occurrences will reset the holddown timer after a
triggered update?
A.) Infinity is finally defined as some max number
B.) HD Timer expires
C.) Another update is received indicating a better metric
D.) The router receives a processing task proportional to
the number of
links in the internetwork
E.) The router detects fault LSP's propagating through the
internetwork
F.) Another update is received indicating net status changed | | 1 |
| What is true when using DDR?
A.) HDLC is the preferred encapsulation
B.) You must use static routing
C.) You should use dynamic routing
D.) You should use ISDN | | 1 |
| Which type of Ethernet framing is used for TCP/IP and
AppleTalk?
A. Ethernet 802.3
B. Ethernet 802.2
C. Ethernet II
D. Ethernet SNAP | Wipro | 1 |
| The following commands were entered at the command prompt of a
Cisco router. What do they accomplish?
access-list 1000 deny 9e.1234.5678.1212 4
access-list 1000 permit -1
interface ethernet 0
ipx network 9e
interface ethernet 1
ipx network 4a
interface serial 0
ipx network 1
ipx output-sap-filter 1000
A. File server advertisements from server 9e.1234.5678.1212
will not be
forwarded on interface S0.
B. All other SAP services, other than file server, from any
source will
be forwarded on S0.
C. All other SAP services, other than print server, from any
source will
be forwarded on S0.
D. Print server advertisements from server 9e.1234.5678.1212
will not be
forwarded on interface S0. | | 1 |
| The following is partial output from a routing table,
identify the
2 numbers in the square brackets; '192.168.10.0 [100/1300]
via 10.1.0.1,
00:00:23, Ethernet1'
A.) 100 = metric, 1300 = administrative distance
B.) 100 = administrative distance, 1300 = hop count
C.) 100 = administrative distance, 1300 = metric
D.) 100 = hop count, 1300 = metric | | 1 |
| |
| For more CCNA Interview Questions Click Here |
along with your userid / name. ThanQ
Site Map
