How does a switch use store and forward? A.) By using a Class I repeater

Advertise your Business Here

Refer this Site

Login | Sign Up


	Do you have a collection of Interview Questions and interested to share with us!! Please send that collection to along with your userid / name. ThanQ

Categories >> Certifications >> Cisco Certifications >> CCNA

CCNA Interview Questions

CCDA Interview Questions

Question

How does a switch use store and forward?

A.) By using a Class I repeater in a collision domain

B.) The LAN switch copies the entire frame into its onboard
buffers and

then looks up the destination address in its forwarding, or
switching,

table and determines the outgoing interface

C.) By using broadcast addresses as source addresses

D.) The switch waits only for the header to be received
before it checks

the destination address and starts forwarding the packets

Question Submitted By :: Guest

I also faced this Question!!

Rank

Answer Posted By

Re: How does a switch use store and forward? A.) By using a Class I repeater in a collision domain B.) The LAN switch copies the entire frame into its onboard buffers and then looks up the destination address in its forwarding, or switching, table and determines the outgoing interface C.) By using broadcast addresses as source addresses D.) The switch waits only for the header to be received before it checks the destination address and starts forwarding the packets

Answer
# 1

Answer: B

Store-and-Forward switching copies the entire frame into its
buffer and

computes the CRC. If a CRC error is detected, the frame is
discarded, or

if the frame is a runt (less than 64 bytes including the
CRC) or a giant

(more than 1518 bytes including the CRC). The LAN switch
then looks up

the destination address in its switching table and
determines the

outgoing interface. The frame is then forwarded to the outgoing

interface. Cisco Catalyst 5000 switches uses the
Store-and-Forward

method. The problem with Store-and-Forward switching is
latency is

increased. Latency also varies with the size of the frame.
The larger

the frame, the more latency associated. This of course is
due to the

fact that the entire frame is copied into its buffer before
being

forwarded.

Is This Answer Correct ?

3 Yes

0 No

Guest

Question	Asked @	Answers
Other CCNA Interview Questions


The "ipx delay number" command will allow an administrator to change the default settings. What are the default settings? A. For LAN interfaces, one tick; for WAN interfaces, six ticks B. For LAN interfaces, six ticks; for WAN interfaces, one tick C. For LAN interfaces, zero ticks; for WAN interfaces, five ticks D. For LAN interfaces, five ticks; for WAN interfaces, zero Ticks		1
Identify the length of an IPX address and it's components? A.) 80 bits, 48 bits network and 32 bits node B.) 32 bits, 16 bits network and 16 bits node C.) None of the above D.) 80 bits, 32 bits network and 48 bits node		1
When you issue the command show version your router returns "Configuration register is 0x0101" From where does the router boot? A. ROM B. NVRAM C. Flash D. a TFTP server		1
Hi Guys I am facing one problem while configuring PAP over Point to Point links. Configuration scenario is like this. ROUTER 1: (Hostname – R1) R1(config)#username R2 password CCNA2 R1(config)#interface serial 1/1 R1(config-if)ip address 10.0.0.1 255.0.0.0 R1(config-if)#lock rate 64000 R1(config-if)#encapsulation ppp R1(config-if)#ppp authentication pap R1(config-if)#ppp pap sent –username R1 password CCNA1 R1(config-if)#no shutdown ROUTER 2: (Hostname – R2) R2(config)#usename R1 password CCNA1 R2(config)#interface serial 1/1 R2(config-if)#ip address 10.0.0.2 255.0.0.0 R2(config-if)#encapsulation ppp R2(config-if)# ppp authentication pap R2(config-if)# ppp pap sent –username R2 password CCNA2 R2(config-if)#no shutdown Now problem is that, after configure the command “ppp authentication pap” the “Line protocol” status goes down on each router. But when I disable this command using “no ppp authentication pap”, the “Line Protocol” status goes up. What could be the problem, can anyone explain it plzzz….!!! Thanks in Advance…!! Shahin..		6
What command do you use to disable domain lookup? A.) no domain-lookup B.) domain no-lookup C.) lookup no-domain D.) no ip domain-lookup		1
How ICMP is used in ping and traceroute facilities		3
Which type of switching reads just the address portion of the frame and then immediately starts forwarding it? A.) Cut-Through B.) Store-and-Forward C.) Tabling D.) Routing E.) Inverse ARP F.) Fast Forward		1
Assume that you are editing a line of text on a Cisco router. What key-stroke combination would take you to the beginning of the line? A.) CTRL-B B.) CTRL-Z C.) CTRL- D.) CTRL-A E.) CTRL- F.) CTRL-		1
Identify the command that displays the SAP table? A.) show ipx servers B.) display SAP table C.) display SAP's D.) show sap table		1
Identify the 4 that are not LAN technologies? A.) HDLC B.) FDDI C.) 802.5 D.) HSSI E.) SDLC F.) Frame Relay	AXA	1
Identify the hardware component that stores the bootstrap program? A.) ROM B.) NVRAM C.) Booter load D.) RAM E.) Flash		2
Identify 2 characteristics of PPP? A.) Uses LLC to establish the link B.) Default serial encapsulation C.) Support multiple layer 3 protocols D.) Offers two types of authentication; PAP and CHAP		1
Which OSI Reference Layer is concerned with logical addressing? A.) Network B.) Transport C.) Datalink D.) Physical E.) Session		1
Identify the 2 types of access-list filters that control SAP traffic? A.) Novell-ether B.) Arpa C.) Input-sap-filter D.) Round-robin E.) Output-sap-filter		1
Why ESP Transport mode is not compatible with NAT????? Though New IP Header in Tunnel mode & Original IP Header in Transport mode are out of Authentication & Encryption.		1
Based upon the 1st octet rule identify the range for a Class A address? A.) 1 - 126 B.) 192 - 223 C.) 128 - 191 D.) 1 - 191		1
Identify 3 features of IGRP? A.) Composite metric B.) New horizon C.) Flash (triggered) updates D.) 60-second periodic updates E.) Poison reverse		1
Can anyone explain in details the STP port state?????		2
Which processes does TCP, but not UDP, use? A. Windowing B. Acknowledgements C. Source Port D. Destination Port		1
"snap" is used by the Cisco IOS for which encapsulation types? A. Ethernet_SNAP B. Token-Ring_SNAP C. FDDI_SNAP D. Novell-SNAP E. Novell-FDDI.		1

For more CCNA Interview Questions Click Here


Copyright Policy \| Terms of Service \| Help \| Site Map 1 \| Articles \| Site Map \| Site Map \| Contact Us \|

Copyright © 2007 ALLInterview.com. All Rights Reserved.

ALLInterview.com :: Forum9.com :: KalAajKal.com