| Other CCNA Interview Questions |
| |
| Question | Asked @ | Answers |
| |
| Identify the command to display the hardware platform
information?
A.) show all
B.) show platform
C.) display hardware
D.) show version | | 1 |
| What field tells the Internet layer how to handle an IP packet?
A. Type of Service
B. Identification
C. Flags
D. Frag Offset | | 1 |
| Describe End to End network services: (Choose all that apply)
A.) Best Route selection
B.) Accomplished Segment by Segment, each segment is autonomous
C.) Flow Control & Data Integrity
D.) Best efforts packet delivery | | 1 |
| When using access lists, what does a Cisco router check first?
A. To see if the packet is routable or bridgeable
B. The destination address
C. The source address
D. The packet contents | | 1 |
| Identify the purpose of ARP?
A.) Avoiding routing loops
B.) Determining a workstation's IP address
C.) Sending a directed broadcast
D.) Determining a workstation's MAC address | | 3 |
| Which IP address and wildcard mask would you use in your
ACL to block all the
hosts in the subnet 192.168.16.43/28? | Siemens | 2 |
| Which two describe frame tagging?
A.) Examines particular info about each frame
B.) A unique ID placed in the header of each frame as it
traverses the
switch fabric
C.) A user- assigned ID defined to each frame
D.) The building of filter tables | | 2 |
| Which of the following is an invalid host address using a
netmask
of 255.255.255.192?
A.) 10.1.1.1
B.) 10.1.1.66
C.) 10.1.1.130
D.) 10.1.1.127 | | 2 |
| Identify the OSI layer associated with bits?
A.) Physical
B.) Network
C.) Binary
D.) Data link | | 1 |
| As system administrator, you type "debug ipx sap" and
receive the following lines as part of the IOS response:
type 0x4, "HELLO2", 199.0002.0003.0006 (451), 2 hops
type 0x4, "HELLO1", 199.0002.0003.0008 (451), 2 hops
What does "0x4" signify?
A. That is a Get Nearest Server response.
B. That it is a General query.
C. That it is a General response.
D. That it is a Get Nearest Server request. | | 1 |
| Which global configuration command will tell the router to load
the IOS file 'IOS_filename' from FLASH memory at the next boot?
A.) boot system flash
B.) boot system flash IOS_filename
C.) boot system IOS_filename flash
D.) boot system tftp IOS_filename tftp_address
E.) config-register 0x0102 IOS_ filename | HSBC | 1 |
| Which addresses are INCORRECTLY paired with their class?
A. 1 to 126, Class A
B. 128 to 191, Class A
C. 1 to 126, Class B
D. 128 to 191, Class B | | 3 |
| The ICMP (referred to in PFC 1700) is implemented by all
TCP/IP hosts
A. true
B. false | | 1 |
| Which command would show all Ethernet interfaces with IPX
configured on them?
A.) show interface ipx ethernet
B.) show ipx interface
C.) show ipx interface ethernet
D.) show ipx
E.) show version
F.) show run | | 1 |
| Using the access-list command, 'access-list 1 deny 2.2.2.2',
what
else must be done to stop host 2.2.2.2 from sending any
traffic out of
physical interface E0,
while still allowing other traffic?
A.) In global mode, Add a line - 'access-list 1 permit
0.0.0.0 255.255.255.255'
B.) On interface E0, Add a line - 'access-group 1 in'
C.) In global mode, Add a line - 'access-list 1 permit all'
D.) On interface E0, Add a line - 'access-list 1 in'
E.) On interface E0, Add a line - 'access-list 1 out'
F.) On interface E0, Add a line - 'ip access-group 1' | | 1 |
| Identify the command to display the hardware platform
information?
A.) show all
B.) show platform
C.) display hardware
D.) show version | | 1 |
| UDP works at which layer of the DOD model?
A.) Internet
B.) Host-to-Host
C.) Transport
D.) Data Link | | 1 |
| Which layer is responsible for negotiating data transfer syntax?
A.) Network
B.) Session
C.) Application
D.) Transport
E.) Presentation | | 2 |
| raid can be used in?
1 NT
2 Netware
3 all of above
mine answer -NT | | 2 |
| Put the following steps of encapsulation into the correct order:
1) The data is broken into segments to be organized
2) Frames are converted to 1s and 0s to be put on the wire
3) Packets are converted into frames
4) Information that users enter is converted into data
5) The segments are changed to packets to be routed
A.) 4, 1, 3, 2, 5
B.) 4, 5, 1, 3, 2
C.) 2, 3, 1, 4, 5
D.) 4, 1, 5, 3, 2 | | 1 |
| |
| For more CCNA Interview Questions Click Here |
along with your userid / name. ThanQ
Site Map
