Which protocol gets a hardware address from a known IP address? A.) RARP

Advertise your Business Here

Refer this Site

Login | Sign Up


	Do you have a collection of Interview Questions and interested to share with us!! Please send that collection to along with your userid / name. ThanQ

Categories >> Certifications >> Cisco Certifications >> CCNA

CCNA Interview Questions

CCDA Interview Questions

Question

Which protocol gets a hardware address from a known IP address?

A.) RARP

B.) TCP

C.) IP

D.) BootP

E.) ARP

F.) ICMP

Question Submitted By :: Guest

I also faced this Question!!

Rank

Answer Posted By

Re: Which protocol gets a hardware address from a known IP address? A.) RARP B.) TCP C.) IP D.) BootP E.) ARP F.) ICMP

Answer
# 1

Answer: E

Address Resolution Protocol - ARP is responsible for
resolving MAC

addresses to IP address. It stores these in its arp cache
for later use.

It does this to inform a lower layer of the destination's
MAC address.

Is This Answer Correct ?

2 Yes

0 No

Guest

Question	Asked @	Answers
Other CCNA Interview Questions


Which layer is responsible for putting 1s and 0s into a logical group? A.) Session B.) Application C.) Transport D.) Data Link E.) Physical F.) Network		1
Which command specifies a second subinterface on serial interface 0? A. interface s 0.2 point-to-point B. interface 2 s.0 point-to-point C. suberinterface 2.s 0 point-to-point D. interface s 0 sub 2 point-to-point E. interface s 0.1 point-to-point sub 2		1
What are the two most common request/reply pair with ICMP messages when using the ping command? (Choose two) A. echo reply B. echo request C. source quench D. fragment onset E. information redirect F. destination reachable G. echo control message		1
What is the maximum hop count for Link-State protocols? A.) 15 B.) there is no hop count limit C.) 256 D.) 16		1
Identify the 2 commands the saves the running-config to NVRAM? A.) write memory B.) copy running-config startup-config C.) write network D.) write backup		2
What parameter is used with statically assigned routers to tell packets which interface to use to reach a distant network? A.) Mask B.) Subnet C.) Default gateway D.) Interface		1
Which OSI Reference Layer controls application to application communication? A.) Datalink B.) Network C.) Transport D.) Session E.) Physical		1
What are the 2 functions of the Data Link Mac layer? A.) Handles access to shared media B.) Manages protocol access to the physical network medium C.) Provides SAPs for higher level protocols D.) Allows multiple devices to uniquely identify one another on the data link layer		1
Which ISDN specification deals with call Setup and Teardown? A.) Q-Series B.) J-Series C.) I- Series D.) C- Series E.) F-Series		1
Which of the following describe full-duplex transmission? A.) Uses a single wire B.) Data transmission in both directions, but only one way at a time C.) Uses a point-to-point connection from the transmitter of the transmitting station to the receiver of the receiving station D.) Data transmission in only one direction		2
Identify the purpose of the Ping command? A.) Share routing information with a neighbor router B.) Transmit user data when buffers are full C.) Test connectivity at layer 3 D.) Test entire protocol stack		1
What information can you get from CDP info: (choose all that apply) A.) Hardware platform B.) One address per protocol C.) Software platform D.) Hostname E.) The same info as show version F.) Incoming/outgoing port		1
Which OSI Reference Layer controls application to application communication? A.) Datalink B.) Network C.) Transport D.) Session E.) Physical		1
Identify the command to determine if CDP is enabled? A.) show enable cdp B.) show cdp enabled C.) show cdp run D.) show cdp		1
In IOS boot sequence if the flash is erased, and there is no access to TFTP server, and we can't load the partial IOS from ROM. Is there any possiblity that we can still boot the router/switch from external PC in which the IOS is installed?		5
Which of the following is a characteristic of a switch, but not of a repeater? A.) Switches forward packets based on the IPX or IP address in the frame B.) Switches forward packets based on the IP address in the frame C.) Switches forward packets based on the MAC address in the frame D.) Switches forward packets based only on the IP address in the packet		2
Which of the following are examples of the Transport Layer? A.) Token Ring B.) UDP C.) TCP D.) IP E.) SQL F.) LLC		2
Identify the 2 methods to modify the routers boot sequence? A.) Setup program B.) Boot system commands C.) RXBoot D.) Config-register		1
Novell NetWare has an Ethernet frame type called Ethernet_SNAP. What is the matching Cisco command line keyword for this encapsulation method? A.) arpa B.) sap C.) snap D.) gns E.) dix F.) novell-ether		1
Which global configuration command will tell the router to load the IOS file 'IOS_filename' from FLASH memory at the next boot? A.) boot system flash B.) boot system flash IOS_filename C.) boot system IOS_filename flash D.) boot system tftp IOS_filename tftp_address E.) config-register 0x0102 IOS_ filename	HSBC	1

For more CCNA Interview Questions Click Here


Copyright Policy \| Terms of Service \| Help \| Site Map 1 \| Articles \| Site Map \| Site Map \| Contact Us \|

Copyright © 2007 ALLInterview.com. All Rights Reserved.

ALLInterview.com :: Forum9.com :: KalAajKal.com