| Other CCNA Interview Questions |
| |
| Question | Asked @ | Answers |
| |
| what is the diffrence betwwen telnet and ssh.this question
is asked by nikhil and i am plasing the answer here insteed
of his personal mail.
| | 4 |
| Which statement is true regarding Administrative distance?
A.) It is a metric
B.) Number of hops between two routers
C.) Trustworthiness of the routing information
D.) RIP Administrative distance is 100 | TCS | 1 |
| What is NOT a characteristic of a network segment on a switch?
A. The segment has its own collision domain
B. The segment can translate from one media to a different media
C. All devices in the segment are part of the same broadcast
domain
D. One device per segment can concurrently send frames to
the switch. | jetking | 1 |
| Identify 3 Fast Ethernet technologies?
A.) 100 Base FastEther
B.) 100 Base FX
C.) 100 Base T4
D.) 100 Base TX | | 1 |
| Which of the following is a valid extended IP access-list?
A.) router(config)# access-list 101 permit tcp host
172.16.30.0 any eq
21 log
B.) router# access-list 101 permit tcp host 172.16.30.0 any
eq 21 log
C.) router(config)# access-list 101 permit any any 172.16.30.0
D.) router(config)# access-list 101 permit ip host
172.16.30.0 any eq 21
log | | 2 |
| What is an administrative distance of 0 mean?
A.) 0 means unbelievable
B.) 0 is for EIGRP
C.) 0 is the default distance for directly connected networks
D.) 0 means unreachable | | 1 |
| Which command will display the encapsulation type on interface
serial 0?
A.) show interface s0
B.) show all
C.) show int s0 encap
D.) show encap s0
E.) show encap | | 1 |
| The following selections show the command prompt and the
configuration of the IP network mask. Which two are
correct?
A. Router#term IP netmask-format { bitcount | decimal |
hexadecimal }
B. Router(config-if)#IP netmask-format { bitcount | decimal
| hexadecimal }
C. Router(config-if)#netmask-format { bitcount | decimal |
hexadecimal }
D. Router#ip netmask-format { bitcount | decimal | hexadecimal } | | 1 |
| Which 3 statements describe default encapsulation and LMI type
configuration?
A.) There are only 4 encapsulations and 3 LMI type options
B.) The LMI type config term options
C.) In release 11.2 the LMI type is autosensed
D.) The default LMI is Cisco
E.) IETF encapsulation must be configured unless the
connecting routers
are both
Cisco | | 1 |
| Which show command should you use to view Frame Relay Local
Management Interface (LMI) Frame statistics?
A. show lmi
B. show ip route
C. show interface
D. show statistics
E. show frame-relay lmi | | 1 |
| The Network layer works with which of the following:
A.) Globules
B.) Bits
C.) Packets
D.) Segments
E.) Frames | | 2 |
| What are two ways IPX supports multiple logical networks on
an individual underrate? (Choose two)
A. network number
B. routing protocol
C. encapsulation type
D. autonomous system number | | 1 |
| Identify the command to reload the router?
A.) Router(config)# reload
B.) Router# reset
C.) Router# reload
D.) Router> reload | | 1 |
| What is required to support full-duplex Ethernet?
A.) Multiple paths between multiple stations on a link
B.) Automatic sensing operation by all connected stations
C.) Loopback and collision detection disabled
D.) Full-duplex NIC cards | | 1 |
| Hi, Jitendra thanks for letting me know my answer. I know
ip addressess classes & there subnet masks. Waht i want to
know is the exact address? Ex.In the organization there are
70 pcs which type of address we can use there what will be
the range for ip address? | | 2 |
| What is the default LMI type for Cisco Routers that are using
Frame-Relay?
A.) Gandalf5
B.) Q933A
C.) Cisco
D.) IETF
E.) ARPA
F.) SAP | | 2 |
| What type of frame does CDP use to gather information about it's
neighbors?
A.) TCP/IP
B.) Novell-ether
C.) Subnetwork Access Protocol (SNAP)
D.) Ethernet_II | | 1 |
| Which can be true regarding VLANs?
A.) They are created by location
B.) They are created by function
C.) They are created by department
D.) They are created by group | | 1 |
| What is the Between Normal Switch and Manageable Switch? | | 11 |
| What’s the default CDP holdtime in seconds for Cisco routers?
| | 2 |
| |
| For more CCNA Interview Questions Click Here |
To Refer this Site to Your Friends 
Site Map
