| Other CCNA Interview Questions |
| |
| Question | Asked @ | Answers |
| |
| Which of the following is true?
A. The default is to send debug output to the console screen.
B. To view debug output from a telnet session, the "terminal
monitor" command must be used
C. If the "logging buffered" command is used, the debug
output would be sent to RAM and can be viewed with the "show
log" command
D. If the "no console loggin" command were configured,
output would besent to a telnet session
E. All of the above
F. None of the above
G. A, B, and C.
H. A, C, D, and E. | | 2 |
| Identify the statement which connects access-list 101 inbound to
interface e0?
A.) Router(config-if)# ip access-group 101 in
B.) Router(config-if)# ip access-group 101
C.) Router(config)# ip access-group 101 e0 in
D.) Router(config)# ip access-group 101 e0 in | | 1 |
| Hi -All
Can you tell me About of NAt (Network Address
Tranlator) bcoz i have no idea about this topics Such as
local ip , global ip and all plz provide the deatil of this
topics | | 3 |
| Select the most correct statement regarding client port
address assignment.
The client port always matches the destination port.
To access a web page the client uses the source port of
80 and the destination port is dynamically selected.
When a client requests a web page the destination port
is 80 by default and the source port for the client is
dynamically selected.
The client source port is 1024 to get web pages and 1055
when retrieving ftp files.
| | 2 |
| Which is not a common problem with Distance-Vector routing?
A.) Slow convergence.
B.) Complex configuration.
C.) Routing loops.
D.) Periodic updates can slow convergence.
E.) Counting to infinity. | | 1 |
| Identify 3 characteristics of ISDN?
A.) Transports voice and data
B.) Transports voice only
C.) Support both BRI and PRI
D.) Runs over existing phone lines
E.) Same as X.25 | | 1 |
| You have OSPF traffic flooding your network
via one of your router interfaces. Write the access
list line that will deny all ospf traffic. Don't
worry about the other lines of the access list. | | 1 |
| In order to enable RIP, which two tasks need to be
performed? (choose two)
A. Specify the routing protocol
B. Confound static RIP routes
C. Specify directly connected subnets
D. Specify directly connected networks | | 1 |
| Which of the following is a routing protocols?
TCP
RIP
SMTP
UDP
| | 2 |
| Identify the 3 methods routers learn paths to destinations?
A.) Dynamic routing
B.) None of the above, configured by default
C.) Default routes
D.) Administrative distance
E.) Static routes | | 1 |
| What type of Ethernet operation allows only one entity to
transmit
at a time? For example, if someone else is transmitting,
they must wait.
A.) Full-Duplex
B.) Dual-Duplex
C.) Half-Duplex
D.) Latex
E.) Quarter-Duplex
F.) Suplex | | 1 |
| Which three types of connectors are commonly associated
with Cisco's V.35 serial cables? (Choose three.)
0 RJ 11
1 DB 60
2 Winchester 15 pin
3 DB 9
4 smart serial
5 RJ 45
| | 3 |
| Identify 2 functions of IPX access-lists?
A.) Control SAP traffic
B.) Limit number of Novell servers on a network
C.) Limit number of workstations on a network
D.) Block IPX traffic | | 1 |
| Identify 2 transport layer protocols?
A.) IP
B.) TCP
C.) CDP
D.) ARP
E.) UDP | | 1 |
| Hi, Jitendra/Shahin
You both are masters of networking na. I am worrying about
my exam. Is it vey tough?because my friend got failed in
ccna. he is very talented person thogh he failed.
| | 1 |
| Identify 3 characteristics regarding CDP?
A.) On by default
B.) Shows only directly connected neighbors
C.) Requires IP or IPX
D.) 60 second update interval by default
E.) 30 second updates interval by default | | 1 |
| Identify 3 Fast Ethernet technologies?
A.) 100 Base FastEther
B.) 100 Base FX
C.) 100 Base T4
D.) 100 Base TX | | 1 |
| Identify the 3 guidelines for routers in the same autonomous
system?
A.) Must be configured for RIP
B.) Interconnected
C.) Assigned the same autonomous system number
D.) Configured for the same routing protocol
E.) Must be same model of router | | 1 |
| here is your question sahin
Hi Jitendera, If i m not wrong, then in EIGRP, Metric weight
is set to K1(Bandwidth)=1, K2(Delay)=0, K3(Reliability)=1,
K4(Load)=0, K5(MTU)=0. This is default setting for EIGRP.
I knew about it from ICND 2 cisco press book.
Three more questions -
a) If we change the K value (I mean metric weight)on a
router what will happen???
b) When redistribution is necessary in EIGRP. Is there any
condition for that???
c) What is reference bandwidth for metric calculation in
EIGRP. As we know, in OSPF, on a CISCO router reference
bandwidth is 10Mbps. | | 3 |
| Given the following IP address from the Class B address
range 172.35.21.12. Your network plan requires no more than
126 hosts on a shored. Which value should you use as the
subnet mask?
A. 255.255.0.0
B. 255.255.128.0
C. 255.255.126.0
D. 255.255.255.128
E. 255.255.255.252 | | 3 |
| |
| For more CCNA Interview Questions Click Here |
Did you received any Funny E-Mails from your Friends and like to share with rest of our friends? Yeah!! you can post that stuff 
Site Map
