| Other CCNA Interview Questions |
| |
| Question | Asked @ | Answers |
| |
| Identify the administrative distance and appropriate routing
protocol?
A.) RIP = 255, IGRP = 100
B.) RIP = 100, IGRP = 120
C.) RIP = 1, IGRP = 0
D.) RIP = 120, IGRP = 100 | | 3 |
| Identify the 2 types of access-list filters that control SAP
traffic?
A.) Novell-ether
B.) Arpa
C.) Input-sap-filter
D.) Round-robin
E.) Output-sap-filter | | 1 |
| Which of the following is a characteristic of a switch, but
not of a
router?
A.) Switches forward packets based on the IPX or IP address
in the frame
B.) Switches forward packets based on the IP address in the
frame
C.) Switches forward packets based on the MAC address in the
frame
D.) Switches forward packets based only on the IP address in
the packet | | 1 |
| There are 2 types of PPP authentication supported by the Cisco
IOS. What are they?
A.) PAP
B.) PREDICTOR
C.) MD5
D.) CHAP
E.) STACKER
F.) MSCHAP | | 1 |
| When you mistakenly type the wrong command
at the Router# prompt the router does a
DNS lookup which takes about 20 seconds.
Which command can you enter to prevent the
router doing this in future?
| | 2 |
| Identify the OSI layer responsible for end-to-end connections?
A.) Network
B.) Transport
C.) Session
D.) Data link
E.) TCP | | 1 |
| Which OSI Reference Layer is concerned with path determination?
A.) Datalink
B.) Physical
C.) Network
D.) Transport
E.) Session | | 2 |
| The maximum distance on a 10BaseT network from the hub to a
workstation is which of the following?
A.) 500 meters
B.) 1000 meters
C.) 100 meters
D.) 1500 meters | | 2 |
| The Internet Control Message Protocol occurs at what layer
of the
seven
layer model?
A.) Physical
B.) Transport
C.) Session
D.) Datalink
E.) Presentation
F.) Network | | 2 |
| Identify the definition of demarcation?
A.) Date in which the WAN service contract expires
B.) Cabling which extends from the WAN service provider to
the customer
C.) Division of responsibility, where the CPE ends and the
local loop
begins
D.) Equipment which is located at the customer premises | | 1 |
| Which is true regarding store-and-forward switching method?
A.) Latency varies depending on frame-length
B.) Latency is constant
C.) It is default for all Cisco switches
D.) It only reads the destination hardware address before
forwarding the
frame | | 1 |
| what hapeen we we configure default root on the router
which is conected by isp
supoese there are two router r1 is conected throug isp and
and by s0 r1 is conexted to r2
if we apply degault root on r1 what will happen | | 3 |
| Identify the prompt displayed if in privileged exec mode?
A.) Router(config)#
B.) Router#
C.) Router>
D.) Router(priv)# | | 1 |
| Which layer hides details of network dependent information from
the higher
layers by providing transparent data transfer?
A.) Transport
B.) Physical
C.) Data Link
D.) Session
E.) Application
F.) Network | | 2 |
| Which Standard IP Access list commands will deny only the source
address 1.1.1.1?
A.) access-list 9 deny host 1.1.1.1
B.) access-list 9 deny 1.1.1.1 255.255.255.0
C.) access-list 9 deny 1.1.1.1 0.0.0.0
D.) access-list 9 deny 1.1.1.1 0.255.255.255
E.) access-list 9 deny 1.1.1.1 255.255.255.255 | | 2 |
| Where would network testing be included in an IP packet?
A. IP Options field
B. Identification field
C. Type of Service field
D. Reservation field | | 1 |
| You need to come up with a TCP/IP addressing scheme for your
company. How many network IDs must you allow for when you
define the
subnet mask for the network?
A.) One for each WAN link
B.) One for each router interface
C.) One for each NIC installed in each client
D.) One for each subnet with hosts
E.) One for each host ID | | 1 |
| Which of the following is true?
A. The default is to send debug output to the console screen.
B. To view debug output from a telnet session, the "terminal
monitor" command must be used
C. If the "logging buffered" command is used, the debug
output would be sent to RAM and can be viewed with the "show
log" command
D. If the "no console loggin" command were configured,
output would besent to a telnet session
E. All of the above
F. None of the above
G. A, B, and C.
H. A, C, D, and E. | | 2 |
| Which of the following is used to manage and monitor the
network?
A.) SNMP
B.) HTTP
C.) IP
D.) FTP | | 2 |
| CPE is an acronym for which of the following?
A.) Customer Premise Equipment
B.) Central Processing Engineering
C.) Customer Process Equipment
D.) Central Processing Equipment | | 2 |
| |
| For more CCNA Interview Questions Click Here |
along with your userid / name. ThanQ
Site Map
