| Other CCNA Interview Questions |
| |
| Question | Asked @ | Answers |
| |
| What is the default LMI type for Cisco Routers that are using
Frame-Relay?
A.) Annex D
B.) Q933A
C.) Cisco
D.) IETF
E.) ARPA
F.) Anex A | | 2 |
| What key do you use to view the last command?
A.) Ctrl+X
B.) Ctrl+Z
C.) Ctrl+E
D.) Ctrl+P | | 2 |
| Identify the command to determine if CDP is enabled?
A.) show enable cdp
B.) show cdp enabled
C.) show cdp run
D.) show cdp | | 2 |
| Identify the default encapsulation on serial interfaces?
A.) ISDN
B.) HDLC
C.) SDLC
D.) Frame Relay
E.) PPP | | 1 |
| Which command successfully pings an individual IP address?
A. Router> ping 192.5.5.0
B. Router# ping 192.5.5.30
C. Router> ping 192.5.5.256
D. Router# ping 192.5.5.255 | | 2 |
| Which of the following are Session Layer standards?
A.) ASCII and EBCDIC
B.) MPEG and MIDI
C.) RPC and SQL
D.) JPEG and PICT | | 1 |
| In regards to the OSI seven-layer model, at which layer is
EBCDIC
and ASCII?
A.) Presentation
B.) Application
C.) Transport
D.) Session
E.) Datalink
F.) Network | | 1 |
| Hi Jitendera, I continuously read your answers which is
more knowlegable than books...
Q.I am facing some problems in subnetting.can you plzz
explain the subnetting process.. will be remain thankful | | 3 |
| Identify the hardware component that stores the backup
configuration?
A.) RAM
B.) NVRAM
C.) Flash
D.) ROM | | 1 |
| Hi, I have packet tracer 5.0. I want to test intervlan
routing routing. Can someone plz tell me about intervlan
routing? | | 1 |
| Which command can verify Application Layer connectivity
between 2
hosts?
A.) ftp
B.) snmp
C.) telnet
D.) ping
E.) traceroute | | 2 |
| Which is true regarding store-and-forward switching method?
A.) Latency varies depending on frame-length
B.) Latency is constant
C.) It is default for all Cisco switches
D.) It only reads the destination hardware address before
forwarding the
frame | | 1 |
| Identify the command to configure DLCI 100 on an interface e0?
A.) Router(config)# frame-relay local-dlci 100
B.) Router(config)# frame-relay local-dlci 100 int e0
C.) Router(config-if)# frame-relay local-dlci 100
D.) Router(config-if)# frame-relay local-dlci 100 int e0 | | 1 |
| What is difference between IPv4 & IPv6?? | Hathway | 3 |
| When setting up a frame-relay network between a Cisco router
and a
non-Cisco router, what encapsulation type should you use?
A.) SAP
B.) CISCO
C.) IANA
D.) Apollo
E.) IETF
F.) Q933A | | 1 |
| Identify the command to display the IP host table?
A.) show ip hostnames
B.) show ip names
C.) show hosts
D.) show ip hosts | | 1 |
| Where is the point between the customers site and the phone
carrier that responsibility changes?
A.) CO
B.) Demarc
C.) DCE
D.) DTE
E.) CPE | | 1 |
| You are given the following address: 128.16.32.13/30.
Determine the subnet mask, address class, subnet address,
and broadcast address.
A. 255.255.255.252, B,128.16.32.12, 128.16.32.15
B. 255.255.255.252, C,128.16.32.12, 128.16.32.15
C. 255.255.255.252, B,128.16.32.15, 128.16.32.12
D. 255.255.255.248, B,128.16.32.12, 128.16.32.15 | | 1 |
| A traffic light is an example of what type of mechanism?
A.) Collision detection
B.) Flow control
C.) Sequence numbering
D.) Network management | | 1 |
| hi... i am usin packet tracer 5.0.. i hav connect two
routers A and B. A has 200.100.25.100 and 1.0.0.1 and router
B has 200.100.50.100 and 1.0.0.2... i hav connected 1.0.0.1
and 1.0.0.2... now i want to route 200.100.25.100 and
200.10.50.100 usin rip.. i enable rip in both the routers...
but whn i give the command show ip route... i jus get this
Codes: C - connected, S - static, I - IGRP, R - RIP, M -
mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA
- OSPF inter area N1 - OSPF NSSA external type 1, N2 - OSPF
NSSA external type 2 E1 - OSPF external type 1, E2 - OSPF
external type 2, E - EGP i - IS-IS, L1 - IS-IS level-1, L2 -
IS-IS level-2, ia - IS-IS inter area * - candidate default,
U - per-user static route, o - ODR P - periodic downloaded
static route Gateway of last resort is not set A# so can
sombody tell me where i hav gone wrong...
thanku | | 4 |
| |
| For more CCNA Interview Questions Click Here |
Site Map
