| Other CCNA Interview Questions |
| |
| Question | Asked @ | Answers |
| |
| Which of the following describe full-duplex transmission?
A.) Uses a single wire
B.) Data transmission in both directions, but only one way
at a time
C.) Uses a point-to-point connection from the transmitter of the
transmitting station to the receiver of the receiving station
D.) Data transmission in only one direction | | 2 |
| What would be the proper wildcard mask to permit all odd
numbered hosts on the 10.48.0.0/12 network?
access-list 1 permit 10.48.0.0 0.15.255.255
access-list 1 permit 10.48.0.1 0.15.255.254
access-list 1 permit 10.48.0.0 0.15.255.1
access-list 1 permit 10.48.0.0 0.0.0.254
access-list 1 permit 10.48.0.0 0.0.0.255
| | 5 |
| Given an IPX network with redundant paths, what command will
configure load balancing?
A.) ipx load-balance
B.) ip maximum-paths 2
C.) ipx maximum-paths 2
D.) ipx load-share | | 1 |
| Which of the following is an example of the Physical Layer?
A.) SQL
B.) IP
C.) LLC
D.) DDP
E.) Ethernet | | 2 |
| What is an advantage of local area network (LAN) segmentation?
A. smaller collision domains
B. elimination of broadcasts
C. decreased cost of implementation
D. larger number of users within the same domain | | 2 |
| Identify the purpose of ARP?
A.) Avoiding routing loops
B.) Determining a workstation's IP address
C.) Sending a directed broadcast
D.) Determining a workstation's MAC address | | 3 |
| Which command displays the IPX SAP table?
A.) show ipx sap
B.) show sap
C.) show ipx interface
D.) show ipx servers
E.) show ipx | | 1 |
| Which statement about the Committed Information Rate (CIP)
is true?
A. It is the rate in bits per second at which the Frame
Relay switch agrees to transfer data
B. It is the clock speed (pod speed) of the connection
(local loop) to the Frame Relay cloud
C. It is the maximum number of bits that switch can
transferduring any Committed Rate Measurement Interval
D. It is a signaling standard between the 3PE device and FP
switch. It is responsible for managing the connection and
maintaining status between the devices. | | 1 |
| What command will not display the status of to1?
A.) show int to1
B.) show to1
C.) show interface to1
D.) show interface | | 1 |
| What is the first step in data encapsulation?
A.) User information is converted into data.
B.) Frames are put into bits.
C.) Data is converted into segments.
D.) Segments are converted into datagrams and packets.
E.) Packets are put into logical frame. | | 1 |
| What 3 sources can configuration commands be placed into RAM?
A.) HP Openview
B.) Console
C.) Vterminal
D.) TFTP server
E.) NVRAM | | 1 |
| The Network layer works with which of the following:
A.) Globules
B.) Bits
C.) Packets
D.) Segments
E.) Frames | | 2 |
| Which OSI layer performs code conversion, code formatting and
encryption?
A.) Physical
B.) Data-Link
C.) Application
D.) Transport
E.) Presentation
F.) Network | | 1 |
| Identify the 3 characteristics of IPX RIP?
A.) Distance vector
B.) Does not support multiple paths
C.) 60 second updates
D.) Default encapsulation is SAP
E.) Uses ticks and hop count as a metric | | 1 |
| Which three are typical operational phases in a basic
connection oriented neloyord service? (Choose three)
A. call setup
B. data transfer
C. load balancing
D. call termination
E. call priortization
F. data segmentation
G. data link identification | | 1 |
| Identify 1 characteristic of RARP?
A.) IP to MAC address translation
B.) Connectionless delivery of packets
C.) Can be used to initiate remote O/S load sequence
D.) Generates error and control messages | | 1 |
| Which configuration mode and command combination sets the
bandwidth metric of a Frame Relay connection?
A. router(config)# clock rate 56
B. router(config)# bandwidth 56
C. router(config)# bandwidth 56000
D. router(config)# clock rate 56000 | | 2 |
| Identify the command to display the configured IP routing
protocols?
A.) show protocols
B.) show protocols all
C.) show routing-protocols
D.) show ip protocols | | 2 |
| Which statement is true regarding half duplex?
A.) Only works in a point-to-point configuration
B.) Allows for transmitting and receiving but not a the same
time
C.) Allow for transmitting and receiving of data simultaneously
D.) Doubles the bandwidth | | 1 |
| What is the bit length and expression form of a MAC address?
A. 24 bits expressed as a decimal number
B. 24 bits expressed as a hexadecimal number
C. 36 bits expressed as a binary number
D. 48 bits expressed as a decimal number
E. 48 bits expressed as a hexadecimal number | | 2 |
| |
| For more CCNA Interview Questions Click Here |
Did you received any Funny E-Mails from your Friends and like to share with rest of our friends? Yeah!! you can post that stuff 
Site Map
