| Other CCNA Interview Questions |
| |
| Question | Asked @ | Answers |
| |
| Which protocol is used for booting diskless workstations?
A.) IP
B.) ARP
C.) RARP
D.) TCP
E.) SNMP | | 2 |
| Which of the following do not belong to the customer?
A.) CO
B.) DCE
C.) Router
D.) CPE
E.) Demarc
F.) DTE | | 1 |
| can we measure how much a host exact bandwidth using by a
network cable which is communicating over the network?
options: 1- via Router 2- Switch, 3- other device... if
yes.. then how ( with every option) | | 3 |
| What is the diiffernce between windows xp & windows 2000?
| VigaTech | 5 |
| Which ISDN protocol prefix specifies switching and signaling?
A.) I
B.) E
C.) Q
D.) S | | 1 |
| What utility can you use to see the path a packet takes
through an
internetwork?
A.) Route
B.) SNMP
C.) Trace
D.) Ping | | 1 |
| what is ip address and what is the difference between the ip
address and mac address why we are not using mac address instead of ip address | IBM | 2 |
| Which service takes information from multiple sources and
allocates bandwidth on a single media?
A. Time-division Multiplexing (TDM)
B. Signaling System 7 (SS7)
C. X.25
D. Frame relay | | 1 |
| To prevent Service Advertisements (SAPs) from flooding a
network, Cisco routers do not forward them. How are
services advertised to other networks?
A. Each router builds its own SAP table and forwards that
every 60 seconds.
B. Each router assigns a service number and broadcasts
that.
C. SAPs aren't necessary with Cisco routers.
D. Cisco routers filter out all SAPs. | | 1 |
| Which of the following are examples of the Session Layer?
A.) TCP
B.) RPC
C.) SQL
D.) NFS
E.) Token Ring | | 1 |
| What do you use the Aux port for?
A.) Console
B.) Terminal editing
C.) Modem
D.) Backup logging | | 2 |
| Identify the purpose of the TCP 3 step handshake?
A.) Setup a un-reliable connection
B.) Initialize routing tables
C.) Synchronize sequence numbers between hosts
D.) Connection tear down process | | 1 |
| Identify the mode reflected by the following prompt 'Router'?
A.) Setup
B.) RXBoot
C.) Boot mode
D.) Privileged exec mode | | 1 |
| Which layer is responsible for flow control,
acknowledgement, and
windowing?
A.) Transport
B.) Network
C.) Application
D.) Session
E.) Physical
F.) Data Link | | 2 |
| what is the difference between a passive and active hub??
which is better ?? | | 5 |
| Which protocol carries messages such as destination
Unreachable, Time Exceeded, Parameter Problem, Source
Quench, Redirect, Echo, Echo Reply, Timestamp, Information
Request, Information Reply, Address Request, and Address
Reply?
A. ICMP
B. UDP
C. TCP
D. TFTP
E. FTP | | 2 |
| Identify the keystroke used to terminate the setup mode?
A.) Ctrl-K
B.) Crtl-C
C.) Ctrl-Z
D.) Crtl-End | | 1 |
| What is a benefit of a virtual LAN (VLAN)?
A. It increases the number of broadcast domains
B. It decreases the number of broadcast domains
C. It increases the numberr of collision domains
D. It decreases the number of collision domains
E. Since it is a vitual Interface it never shuts down | | 3 |
| Which type of switching reads in the entire frame before
forwarding it?
A.) Tabling
B.) Store-and-Forward
C.) Inverse ARP
D.) Fast Forward
E.) Cut-Through
F.) Routing | | 1 |
| What does the IPX maximum path command do?
A.) Allows you to disable the TTL on an IPX packet
B.) This parameter is only used in NLSP routing
C.) Sets the maximum metric that can appear in the routing table
D.) Configures round robin load sharing over multiple equal
metric paths
(parallel paths) | | 1 |
| |
| For more CCNA Interview Questions Click Here |
To Refer this Site to Your Friends 
Site Map
