| Other CCNA Interview Questions |
| |
| Question | Asked @ | Answers |
| |
| 8. When is Frame Tagging used?
A. When you install repeaters in your network
B. When you install bridges in your network
C. When you install routers in your network
D. When you use Switches configured with multiple VLANS
| | 4 |
| Which layer is responsible for routing through an internetwork?
A.) Physical
B.) Session
C.) Network
D.) Transport
E.) Application
F.) Data Link | | 1 |
| Which of the following is not a characteristic of link-state
routing protocols?
❍ A. VLSM support
❍ B. Route summarization at any bit level
❍ C. Full routing updates at regular intervals
❍ D. Discontiguous network support | | 1 |
| Hello Every one. Actually its my first time to using this
site and first time to posting a question. Actually i need
to know about CCNA Exam. Please can any one tell me about
the Exam style and any recommendation for study? Best
Regards to all the Friends | | 1 |
| From Enable mode, a user types the letter 'C' and presses enter.
There is more than 1 command that starts with 'C'. What
message would
the router return?
A.) Nothing would be returned, the command is simply ignored.
B.) unknown command
C.) ambiguous command.
D.) Copy to?
E.) Configured console from console. | | 1 |
| Identify the command that specifies Serial 0 in slot 1?
A.) Router(config)# interface serial1/1
B.) Router(config)# interface serial1/0
C.) Router(config)# interface serial0.1
D.) Router(config)# interface serial0/1 | | 4 |
| Why we choose the router rather then L-3 Switch | Network-Solutions | 7 |
| You are conferring a Frame Relay router with subinterfaces
on interface Serial 0 Which subinterfaces numbers could you
use for this configuration?
A. 1 and 2
B. 0 2 and 0 3
C. 1 0 and 1 1
D. 0 1 a and 0 1 | | 1 |
| The Cisco Catalyst 5000 switch supports full duplex. How
would you
enable it on the second port of the card in slot 1?
A.) router(config-if)# duplex full
B.) router(config)# duplex full
C.) router(config-if)# set port duplex
D.) router(config)#port duplex = full
E.) router(config-if)# set port 1/2 full | | 1 |
| tell me our traditional ip routing is what
A--conectless
b----conection orented
c-----pacekt switching
d------ckt switching
slect any two
this is the question which i forgot to incoprate
next-questions
| | 3 |
| The Internet Control Message Protocol occurs at what layer
of the
seven
layer model?
A.) Physical
B.) Transport
C.) Session
D.) Datalink
E.) Presentation
F.) Network | | 2 |
| here is your question sahin
Hi Jitendera, If i m not wrong, then in EIGRP, Metric weight
is set to K1(Bandwidth)=1, K2(Delay)=0, K3(Reliability)=1,
K4(Load)=0, K5(MTU)=0. This is default setting for EIGRP.
I knew about it from ICND 2 cisco press book.
Three more questions -
a) If we change the K value (I mean metric weight)on a
router what will happen???
b) When redistribution is necessary in EIGRP. Is there any
condition for that???
c) What is reference bandwidth for metric calculation in
EIGRP. As we know, in OSPF, on a CISCO router reference
bandwidth is 10Mbps. | | 3 |
| UDP works at which layer of the DOD model?
A.) Internet
B.) Host-to-Host
C.) Transport
D.) Data Link | | 1 |
| What is the command to copy the IOS image to a TFTP server?
A.) copy flash tftp
B.) copy running-config tftp
C.) copy ios tftp
D.) copy startup-config tftp | | 2 |
| Identify 3 IP applications?
A.) AURP
B.) ARP
C.) Telnet
D.) SMTP
E.) DNS
F.) RARP | | 2 |
| If you are running Token Ring with Novell IPX routing, which
encapsulation
should you use?
A.) SAP
B.) SNAP
C.) 802.5
D.) 802.2 | | 1 |
| How do you set the encapsulation type to PPP for an interface?
A.) encap ppp
B.) ppp encapsulation
C.) encapsulation ppp
D.) encapsulation ppp enable
E.) ppp enable encapsulation | | 2 |
| Where is the backup configuration file stored?
A.) RAM
B.) ROM
C.) Console
D.) NVRAM | | 1 |
| What three occurrences will reset the holddown timer after a
triggered
update?
A.) Infinity is finally defined as some max number
B.) HD Timer expires
C.) Another update is received indicating a better metric
D.) The router receives a processing task proportional to
the number of
links in the internetwork
E.) The router detects fault LSP's propagating through the
internetwork
F.) Another update is received indicating net status changed | | 1 |
| What is the command to copy the IOS image to a TFTP server?
A.) copy flash tftp
B.) copy running-config tftp
C.) copy ios tftp
D.) copy startup-config tftp | | 2 |
| |
| For more CCNA Interview Questions Click Here |
To Refer this Site to Your Friends 
Site Map
