ALLInterview.com :: Home Page KalAajKal.com
 Advertise your Business Here     
Browse  |   Placement Papers  |   Company  |   Code Snippets  |   Certifications  |   Visa Questions
Post Question  |   Post Answer  |   My Panel  |   Search  |   Articles  |   Topics  |   ERRORS new
   Refer this Site  Refer This Site to Your Friends  Site Map  Bookmark this Site  Set it as your HomePage  Contact Us     Login  |  Sign Up                      
tip       Ask Questions on ANYTHING, that arise in your Daily Life at     FORUM9.COM
Google
 
Categories  >>  Certifications  >>  Cisco Certifications  >>  CCNA
 
 


 

 
 CCNA interview questions  CCNA Interview Questions
 CCDA interview questions  CCDA Interview Questions
Question
What is the routing algorithm used by RIP and IGRP?

A.) OSPF

B.) Link-state

C.) Dynamic

D.) Distance Vector
 Question Submitted By :: Guest
I also faced this Question!!     Rank Answer Posted By  
 
  Re: What is the routing algorithm used by RIP and IGRP? A.) OSPF B.) Link-state C.) Dynamic D.) Distance Vector
Answer
# 1
Answer: D

Distance vector-based routing algorithms (also known as
Bellman-Ford

algorithms) pass periodic copies of a routing table from
router to

router. Regular updates between routers communicate topology
changes.

Each router receives a routing table from it's direct
neighbor and

increments all learned routes by one. By this method, each
router learns

the internetwork topology via second hand information.
 
Is This Answer Correct ?    4 Yes 0 No
Guest
 
  Re: What is the routing algorithm used by RIP and IGRP? A.) OSPF B.) Link-state C.) Dynamic D.) Distance Vector
Answer
# 2
D.) Distance Vector
 
Is This Answer Correct ?    6 Yes 0 No
Kapilasdhir
[Pioneer]
 
 
 

 
 
 
Other CCNA Interview Questions
 
  Question Asked @ Answers
 
Identify the command that will display the RIP routes entering and leaving the router? A.) Router(config)# debug ip rip B.) Router# debug ip rip C.) Router>debug ip rip D.) Router# debug rip routes  1
What is link aggregration?? How many types of protocol are used on that??? Hathway3
Inverse ARP serves what purpose? A.) Method for a local router to introduce itself to the remote end of the connection B.) Broadcast a routing table update C.) Identify MAC addresses if the IP address is known D.) Sent every 10 seconds used to verify the Frame Switch is still active  1
what is used for passive intercae comand mine answer-to prevent to take update from outside  1
When you use the Cisco IOS command show configuration on a router which part of the output shows the specific conferred IP addresses and shored masks? A. the IP host table B. the interfaces output C. each section of the output D. the global configuration statements E. the section under the autonomous system number  1
What are the difference between IPv4 & IPv6?? Can anyone explain more details about it..!! HCL4
When you enter router passwords during the setup dialog what is the difference between enable and the enable secret passwords? A. The enable password is encrypted B. The enable secret password uses IPSec password authentication C. The enable secret password cannot be seen as clear text when viewing the configuration D. The enable secret password acts as a backup in case the enable password is compromised Wipro6
What are hold-downs used for? A.) To prevent regular update messages from reinstating a route that has come back up B.) Information received on an interface cannot be sent back out the same interface C.) To prevent regular update messages from reinstating a route that has gone down D.) To hold the routing table from being sent to another router  1
Identify the keystroke to position the cursor to the beginning of a command line? A.) Ctrl-A B.) Ctrl-Ins C.) Ctrl-B D.) Ctrl-Z  1
What is switch priority & why it is used???? ADP4
What is the command to copy the IOS image to a TFTP server? A.) copy flash tftp B.) copy running-config tftp C.) copy ios tftp D.) copy startup-config tftp  2
Which of the following is an example of the Network Layer? A.) TCP B.) IP C.) SQL D.) Token Ring E.) LLC  1
Which of the following are logged when IP access list logging is enabled? A.) source address B.) protocol C.) source port D.) destination address E.) access list number F.) destination port  1
Which of the following would be displayed by the command 'SHOW CDP NEIGHBOR DETAIL'? A.) The incoming/outgoing port. B.) The hardware platform. C.) One address per protocol. D.) Amount of Flash Memory Available E.) The routers hostname. F.) The subnet mask, if IP is configured.  1
Identify the command that displays traffic statistics on serial0/1? A.) display interface serial0/1 B.) show interface serial0/1 C.) show seria0/1 stats D.) show interface serial0/1 stats  1
Which device listed below provides clocking for the line? A.) DCE B.) CPE C.) CO D.) DTE E.) Demarc  2
How many Frame-relay encapsulation types are available with Cisco routers? A.) Four B.) Two C.) Five D.) Three  2
The ICMP (referred to in PFC 1700) is implemented by all TCP/IP hosts A. true B. false  1
what is the need og jitu(config)#ip helper address <ip address> can any one exaplain it briefly specially shain i am looking towards you.Becoz you are the only one who can solve my that problem not even jitendera sinha  3
What is the command to allow you to type Tokyo instead of the IP address 172.16.30.1 to access a router named Tokyo? A.) config t, ip host Tokyo 172.16.30.1 B.) config t, ip hostname Tokyo 172.16.30.1 C.) config t, hostname Tokyo 172.16.30.1 D.) config t, ip hostname 172.16.30.1 Tokyo  1
 
For more CCNA Interview Questions Click Here 
 
 
 
 
 
   
Copyright Policy  |  Terms of Service  |  Help  |  Site Map 1  |  Articles  |  Site Map  |   Site Map  |  Contact Us interview questions urls   External Links 
   
Copyright © 2007  ALLInterview.com.  All Rights Reserved.

ALLInterview.com   ::  Forum9.com   ::  KalAajKal.com