| Other CCNA Interview Questions |
| |
| Question | Asked @ | Answers |
| |
| Identify the 3 characteristics of IGRP?
A.) Uses hop count as a metric
B.) Supports multiple unequal paths
C.) Administrative distance is 100
D.) Configured with an Automous system number
E.) Link state | | 1 |
| Which router command allows you to determine if an IP access
list is enabled on a particular interface?
A. Router# show ip interface
B. Router> show access-list
C. Router# show ip access-list
D. Router> show interface ip access-list
E. Route 1 P.O. box 198 | | 2 |
| Identify the command to run 'setup'?
A.) Router(config)#setup
B.) Router?setup
C.) Router#setup
D.) Router>setup | Karrox | 1 |
| Which of the following will apply IPX sap access list 1010 for
incoming traffic, assume you are at the interface configuration?
A.) ipx input-sap-filter 1010 in
B.) ipx input-sap-filter 1010
C.) ipx access-group 1010 in
D.) ipx access-list 1010 in | | 1 |
| Suppose we have 4 switches runing in VTP mode. So when i
create a VLAN in Server Switch this VLAN info reflect in all
other switch. So question is -
A) Suppose i m practicing this scenario in BOSON software,
When a create a VLAN in server switch n ADD ports of switch
to that VLAN, the same number of ports of client switch also
belongs to dat VLAN.
For example - In switch A (Server mode), i create a VLAN 7
name Hyderabad & port number 1, 2 & 3 put into this VLAN.
Another Switch B (Client mode), its also showing that port
number 1,2 & 3 belong the same VLAN.
How cud it possible... As we know, VTP share only VLAN
configuration information. Cud anyone explain it please....!!!!
B)Same thing, when i m practicing in PACKET TRACER 5.0, its
only showing that VLAN configuration information is shared.
No port information is shared at all. I can manually
configure individual switch port to respective VLAN as our wish.
Cud anyone explain it please..!!!
| | 3 |
| How ICMP is used in ping and traceroute facilities | | 3 |
| Which OSI Reference Layer is concerned with path determination?
A.) Datalink
B.) Physical
C.) Network
D.) Transport
E.) Session | | 2 |
| what is vlan and how will you configure vlan on 3650
switch and how many valn can you create on that switch | Volvo | 3 |
| What is the result of segmenting a network with a router
into segments 1 and 2?
A. It increases the number of collisions
B. It decreases the number of broadcast domains
C. It connects segment 1 and broadcasts to segment 2
D. It connects segment 1 and broadcasts from genre to segment 2 | | 1 |
| What is the Network Layer of the OSI responsible for?
A.) Bridging
B.) Routing packets through an internetwork
C.) Regenerating the digital signal
D.) Gateway services | | 2 |
| what is the subnet for the host ip address 172.16.210.0/22 | IBM | 4 |
| What is the juncture at which the CPE ends and the local loop
portion of the service begins?
A. Demarc
B. CO
C. Local loop
D. Last-mile | | 1 |
| Which command successfully pings an individual IP address?
A. Router> ping 192.5.5.0
B. Router# ping 192.5.5.30
C. Router> ping 192.5.5.256
D. Router# ping 192.5.5.255 | | 2 |
| Which processes does TCP, but not UDP, use?
A. Windowing
B. Acknowledgements
C. Source Port
D. Destination Port | | 1 |
| What is the last step in data encapsulation?
A.) User information is converted into data.
B.) Segments are converted into datagrams and packets.
C.) Frames are put into bits.
D.) Data is converted into segments.
E.) Packets are put into logical frame. | | 1 |
| What does -1 signify in an extended IPX access list?
A. permit this host
B. deny this host
C. permit only this subnet
D. any host or any network | | 2 |
| What protocols can you use while testing Trace?
A.) DECnet
B.) CLNS
C.) IP
D.) Old Vines
E.) Vines
F.) Chaos | | 1 |
| Identify 2 functions of IPX access-lists?
A.) Control SAP traffic
B.) Limit number of Novell servers on a network
C.) Limit number of workstations on a network
D.) Block IPX traffic | | 1 |
| (1)what is "rtp" and how it work,
(2)what is diffrence between igrp and eigrp
(3)the slection prcedure of dr and bdr is depend open
(4)why frame really is called nbma
(5)what is ppp
(6) what is diffrence b/w tcp and udp
(7) how can we implement ospf protocall on any router
(8)whta is as nomber
(9)what is AD value
(10)what is the broadcast id,n/w id and number of vallid
host of the 255.255.255.128/25 195.168.10.10/25
(11) what is stub network
(12) what is contigues n/w
(13)on which type of router we can implement default routing
(14)what is diffrence b/w hub switch;switch router,
(15)what is v lan
(16)what is the diffrence b/w link sate protocal and
distance vector protocall
(17)what is synchoransh mode of data transfer and
asynchronash mode of data transfer
(18) question on lab,
belive me frnds there are 20 questions and 5 questions on
lab implimentaion.around 1.1/2 hour i was in interview room
and after givieng 17 right answera and 4 in lab i got
slected
try to give answer
if any difficulty or any prob plz email me on
jitenderasinha.it@gmail.com
if any one of you havae boson netsim plz also intimate me
| | 4 |
| Which of the following are Distance Vector protocols?
A.) IGRP
B.) RIP
C.) OSFP
D.) EIGRP | | 3 |
| |
| For more CCNA Interview Questions Click Here |
To Refer this Site to Your Friends 
Site Map
