| Other CCNA Interview Questions |
| |
| Question | Asked @ | Answers |
| |
| What is the command to start IP RIP version 1 routing on a
Cisco router?
A. show rip
B. enable rip
C. router enable
D. router rip | | 5 |
| What is a characteristic of Store and Forward switches?
A.) They forward the frame before it is completely read.
B.) They work at wire speed.
C.) They are the same a Cut-Through switching.
D.) They read the entire frame and check CRC before forwarding.
E.) They decrease latency. | | 1 |
| What three occurrences will reset the holddown timer after a
triggered
update?
A.) Infinity is finally defined as some max number
B.) HD Timer expires
C.) Another update is received indicating a better metric
D.) The router receives a processing task proportional to
the number of
links in the internetwork
E.) The router detects fault LSP's propagating through the
internetwork
F.) Another update is received indicating net status changed | | 1 |
| Which commands would assign and enable IPX on an interface ?
A.) enable netware
B.) enable novell-ether
C.) router#(config)ipx routing
D.) You must first enable IPX globally and then
assign the network number to the interface .
E.) enable ipx
F.) router#(config-if)ipx network 4a | | 1 |
| What is the difference between OSPF Exteral Type 1 (O E1) &
External Type 2 (O E2) routes???? | | 3 |
| What must be true for two routers running IGRP to communicate
their routes?
A.) Same autonomous system number
B.) Connected using Ethernet only
C.) Use composite metric
D.) Configured for PPP | | 1 |
| What is the meaning of PASSIVE interface in RIP, IGRP, EIGRP
& OSPF??
Can any one explain..!!! | | 4 |
| Extended IP access-lists (100-199) can be used to control
traffic.
Which command listed below will permit smtp mail to only
host 3.4.5.6 ?
A.) It is not possible for SMTP traffic
B.) access-list 102 permit tcp any host 3.4.5.6 eq smtp
C.) access-list 101 permit tcp any 3.4.5.6 0.0.0.0 eq 23
D.) access-list 102 permit tcp any any eq smtp
E.) access-list 101 permit tcp any 3.4.5.6 0.0.0.0 eq 25 | | 1 |
| What does the acronym ARP stand for?
A.) Address Resolution Phase
B.) ARP Resolution Protocol
C.) Address Resolution Protocol
D.) Address Recall Protocol | | 2 |
| Whith the hierarchical numbering of IP addressing what
determines the spoon of the address that will identify the
network number?
A. subnet mask
B. dots between octets
C. class of the first octet
D. assignments of DHCP
E. address resolution process | | 1 |
| Inverse ARP serves what purpose?
A.) Method for a local router to introduce itself to the
remote end of the
connection
B.) Broadcast a routing table update
C.) Identify MAC addresses if the IP address is known
D.) Sent every 10 seconds used to verify the Frame Switch is
still active | | 1 |
| 1 whatis te1,te2 and nt1 what is threre functions
2 what are the isdn protocols
3 whait is spid | | 1 |
| On an ISDN BRI interface, the control channel is the 'D'
channel.
What is the rate of this channel?
A.) 64 Kbps
B.) 1.544 Mbps
C.) 128 Kbps
D.) 2.048 Mbps
E.) 16 Kbps | | 4 |
| What is the Cisco name for the encapsulation type used on a
serial interface?
A. HDLC
B. SDLC
C. SAP
D. SNAP | | 3 |
| Which command displays access list 111?
A. show access-list 111
B. show ip access-list 111
C. display ip access-list 111
D. display access-list 111 details | Satyam | 6 |
| Identify the 2 commands that save the running-config to a TFTP
server?
A.) write running tftp
B.) copy running network
C.) copy running tftp
D.) write network | | 1 |
| Hi,can anyone explain me in brief about ccna security.
waiting for your answer | | 2 |
| Identify the command that configures the bandwidth to 56K?
A.) Router(config-if)# bandwidth 56000
B.) Router(config-if)# bandwidth 56k
C.) Router(config)# bandwidth 56
D.) Router(config-if)# bandwidth 56 | | 1 |
| What are characteristics of UDP
A. It is reliable and acknowledged
B. It is unreliable and acknowledged
C. It is reliable and unacknowledged
D. It is unreliable and unacknowledged | | 2 |
| How do you disable CDP on the entire Router?
A.) Router#no cdp run
B.) Router(config-if)# no cdp enable
C.) Router(config)# no cdp enable
D.) Router(config)# no cdp run | | 1 |
| |
| For more CCNA Interview Questions Click Here |
Did you received any Funny E-Mails from your Friends and like to share with rest of our friends? Yeah!! you can post that stuff 
Site Map
