| Other CCNA Interview Questions |
| |
| Question | Asked @ | Answers |
| |
| Which of the following are examples of the Application Layer?
A.) LLC
B.) Token Ring
C.) Spreadsheet
D.) TCP
E.) IP
F.) Word Processor | | 1 |
| Which line from a show spantree 1 command output indicates
that virtual LAN 1 (VLAN1) is functioning properly?
A. Root pod is FastEthernet 0/26
B. Port Ethernet 0/1 of VLAN1 is Forwarding
C. Designated port is Ethernet 0/1, path cost 10
D. Designated root has priority 0 address 00D0 588F B600
E. VLAN1 is executing the IEEE compatible Spanning Tree Protocol | | 1 |
| Given the following IP address from the Class C address
range 192.168.21.12. Your network plan needs addresses for
28 small prkps Each office uses its own shored. The
network design specifies that you confound for five bits of
subnetting. When you confound for this in Cisco IOS
software which shored mask should you use?
A. 255.255.0.28
B. 255.255.255.0
C. 255.255.255.28
D. 255.255.255.248
E. 255.255.255.252 | | 1 |
| what is diffrence betwwen mpls and frame really | Volvo | 1 |
| Identify the 2 commands that copies the configuration in
NVRAM to
RAM?
A.) copy backup-config running-config
B.) configure nvram
C.) copy startup-config running-config
D.) configure memory | | 2 |
| What command will not display the status of to1?
A.) show int to1
B.) show to1
C.) show interface to1
D.) show interface | | 1 |
| Which of these is the Private key?
A. Bear
B. Cave
C. Indian
D. Cowboy | | 1 |
| Hi Guys
I am facing one problem while configuring PAP over Point to
Point links. Configuration scenario is like this.
ROUTER 1: (Hostname – R1)
R1(config)#username R2 password CCNA2
R1(config)#interface serial 1/1
R1(config-if)ip address 10.0.0.1 255.0.0.0
R1(config-if)#lock rate 64000
R1(config-if)#encapsulation ppp
R1(config-if)#ppp authentication pap
R1(config-if)#ppp pap sent –username R1 password CCNA1
R1(config-if)#no shutdown
ROUTER 2: (Hostname – R2)
R2(config)#usename R1 password CCNA1
R2(config)#interface serial 1/1
R2(config-if)#ip address 10.0.0.2 255.0.0.0
R2(config-if)#encapsulation ppp
R2(config-if)# ppp authentication pap
R2(config-if)# ppp pap sent –username R2 password CCNA2
R2(config-if)#no shutdown
Now problem is that, after configure the command “ppp
authentication pap” the “Line protocol” status goes down on
each router. But when I disable this command using “no ppp
authentication pap”, the “Line Protocol” status goes up.
What could be the problem, can anyone explain it plzzz….!!!
Thanks in Advance…!!
Shahin..
| | 6 |
| What is the protocol and what is the second part of the
following network address? 172.16.0.254 mask - 255.255.0.0
A. IPX MAC address
B. IP Class C directed broadcast
C. Private IP address node number
D. Public IP directed broadcast
E. Private IP directed broadcast | | 1 |
| How many valid host IP addresses are available on the
following network/subnetwork? 176.12.44.161/30
A. 2
B. 30
C. 254
D. 16,382
E. 65,534 | | 1 |
| Which OSI layer handles physical addresses and network topology?
A.) Presentation
B.) Physical
C.) Transport
D.) Application
E.) Data-Link
F.) Network | | 2 |
| Which three are typical operational phases in a basic
connection oriented network service?
A. call setup
B. data transfer
C. load balancing
D. call termination
E. caller ID
F. call prionflication
G. data segmentation
H. data and momma
I. data link identification
J. callering book | | 1 |
| What is the command to start IP RIP version 1 routing on a
Cisco router?
A. show rip
B. enable rip
C. router enable
D. router rip | | 5 |
| Identify the command to display all the valid commands at the
given mode?
A.) Help all
B.) Help
C.) All commands
D.) ? | | 2 |
| You have a Class B network address divided into 30 subnets. You
will add 25 new subnets within the next year. You need 600
host IDs for
each subnet. Which subnet mask should you use?
A.) 255.254.0.0
B.) 255.192.0.0
C.) 255.255.252.0
D.) 255.255.248 0 | | 1 |
| Repeaters work at which layer of the OSI model?
A.) Network
B.) Session
C.) Transport
D.) Physical | | 3 |
| A router on one side of a PPP link uses the resonance RTR1
and the password COPP1-PWD. Which configuration line on
RTR1 enables a connection between RTR1 and another router
named RTR2?
A. username, RTR2 password COPR1-PWD,
B. username, RTR1 password COPR1-PWD,
C. username, RTR2 password COPR2-PWD,
D. username, RTR1 password COPR2-PWD, | | 1 |
| Identify the default encapsulation on serial interfaces?
A.) ISDN
B.) HDLC
C.) SDLC
D.) Frame Relay
E.) PPP | | 1 |
| Which three basic switch functions increase available
bandwidth on the networks? (Choose three)
A. loop avoidance
B. address learning
C. hop count limiting
D. broadcast filtering
E. packet forward/filtering | | 3 |
| Identify the keystroke used to terminate the setup mode?
A.) Ctrl-K
B.) Crtl-C
C.) Ctrl-Z
D.) Crtl-End | | 1 |
| |
| For more CCNA Interview Questions Click Here |
Site Map
