| Other CCNA Interview Questions |
| |
| Question | Asked @ | Answers |
| |
| Identify 2 features of PPP CHAP authentication?
A.) Username and password is sent in clear text
B.) Authentication messages are sent periodically during the
connection
C.) Less secure then PAP
D.) Local router 'challenges' the remote router | | 1 |
| Which can be true regarding VLANs?
A.) They are created by location
B.) They are created by function
C.) They are created by department
D.) They are created by group | | 1 |
| Which NetWare protocol provides link-state routing?
A. NLSP
B. RIP
C. SAP
D. NCP | | 1 |
| In order to configure a Frame Relay subinterface with IP
identify
the 2 commands that must be configured on the physcial
interface?
A.) Router(config-if)# encapsulation frame-relay
B.) Router(config-if)# no ip address
C.) Router(config-if)#encapsulation subinterface frame-relay
D.) Router(config)# subinterface s0 encapsulation frame-relay | | 2 |
| Which two protocol tools use ICMP? (Choose two)
A. ping
B. telnet
C. configure
D. traceroute
E. show commands
F. standard access lists | | 3 |
| Identify the components in the following command 'interface
serial0/1/1'
A.) Serial interface, port number 0, slot 1, port adapter 1
B.) Serial interface, slot 1, port number 1, port adapter 0
C.) Serial interface, slot 0, port adapter 1, port number 1 | | 2 |
| Most routing protocols recognize that it is never useful to send
information about a route back out the direction from which
the original
packet came. This is an example of which routing technology?
A.) Split Horizon
B.) LMI
C.) Triggered Updates
D.) Poison Reverse
E.) SYN, ACK
F.) DLCI | | 1 |
| Your Ethernet interface currently has the IP address of
1.1.1.1/24. You would like it to have a second IP address of
2.2.2.2/24.
Which command will do that?
A.) ip address 1.1.1.1 2.2.2.2 255.255.255.0
B.) ip address 2.2.2.2 255.255.255.0 secondary
C.) ip address 2.2.2.2 255.255.255.0
D.) This cannot be done, you can only have 1 IP address per
physical
interface.
E.) ip address 2.2.2.2 /24 | | 1 |
| How do you disable advanced editing?
A.) terminal editing
B.) terminal no editing
C.) disable editing
D.) no terminal editing | | 2 |
| Which can be logged by IPX extended access lists?
A.) source address
B.) protocol
C.) source socket
D.) access list number
E.) destination socket
F.) destination address | | 1 |
| Identify the 3 key features of the Cisco Discovery Protocol?
A.) Off by default
B.) Will allow for the discovery of layer 3 addresses on
neighbor routers
C.) Verify connectivity
D.) Open standard
E.) Does not require any layer 3 protocols to be configured | | 1 |
| What command can be used to test IPX connectivity?
A.) Ping 2e.000.0045.8923
B.) Ping 192.168.100.1
C.) Ping ipx 2e.0000.0045.8923
D.) Ipx ping 2e.0000.0045.8923 | | 1 |
| LAN stands for which of the following?
A.) Local Area Network
B.) Local Arena Network
C.) Local Area News
D.) Logical Area Network | | 1 |
| Identify 3 features of IGRP?
A.) Composite metric
B.) New horizon
C.) Flash (triggered) updates
D.) 60-second periodic updates
E.) Poison reverse | | 1 |
| Identify 1 characteristic of RARP?
A.) MAC to IP address translation
B.) Connectionless delivery of packets
C.) Can be used to initiate remote O/S load sequence
D.) Generates error and control messages | | 3 |
| What is the Broadcast MAC Address? | Avaya | 2 |
| Which of the following is True regarding passwords on a
Cisco router?
A. All passwords can be encrypted
B. All passwords can be entered using the set-up dialogue
C. A password can be set before a user can enter the
privileged mode
D. A password can be set for individual lines
E. TACACS or Radius password authentication can be used. | | 1 |
| Which service takes information from multiple sources and
allocates bandwidth on a single media?
A. Time-division Multiplexing (TDM)
B. Signaling System 7 (SS7)
C. X.25
D. Frame relay | | 1 |
| Identify the following components of the IPX address
2e.0000.0065.ed43
A.) Not a valid IPX address
B.) Network = 2e, Subnet = 0000, Node = 0065.ed43
C.) Network = 2e.0000, Node = 0065.ed43
D.) Network = 2e, Node = 0000.0065.ed43 | | 1 |
| what is standard and extended acess list?
what are the commands for extended and acess list? | HCL | 3 |
| |
| For more CCNA Interview Questions Click Here |
Ask Questions on ANYTHING, that arise in your Daily Life at 
Site Map
