| Other CCNA Interview Questions |
| |
| Question | Asked @ | Answers |
| |
| All equipment located at the customers site is called:
A.) CPE
B.) CO
C.) DCE
D.) Demarc
E.) DTE | | 1 |
| The administrator of a comapny needs to ensure that a web
server in
their network is accessible from the Internet. Since the
network uses private
addressing, this requires an IP-to-registered-address
mapping. The following
command is entered on the router:
router(config)# ip nat inside source static 192.168.2.1
198.18.1.254
After unsuccessful results from a ping to the Internet, the
administrator issues the
show ip nat translations command and the output is blank.
What could be the
problem with the NAT configuration for this mapping?
A. The keyword overload is missing from the command.
B. The administrator needs to define a NAT pool first.
C. An access list must be defined to create static NAT
translations.
D. The interfaces need to be configured for NAT. | | 4 |
| What are the 2 functions of the Data Link Mac layer?
A.) Handles access to shared media
B.) Manages protocol access to the physical network medium
C.) Provides SAPs for higher level protocols
D.) Allows multiple devices to uniquely identify one another
on the data
link layer | | 1 |
| here is your question sahin
Hi Jitendera, If i m not wrong, then in EIGRP, Metric weight
is set to K1(Bandwidth)=1, K2(Delay)=0, K3(Reliability)=1,
K4(Load)=0, K5(MTU)=0. This is default setting for EIGRP.
I knew about it from ICND 2 cisco press book.
Three more questions -
a) If we change the K value (I mean metric weight)on a
router what will happen???
b) When redistribution is necessary in EIGRP. Is there any
condition for that???
c) What is reference bandwidth for metric calculation in
EIGRP. As we know, in OSPF, on a CISCO router reference
bandwidth is 10Mbps. | | 3 |
| Given the following static route command, 'ip route 3.3.3.0
255.255.255.0
4.4.4.4 125', which portion represents the administrative
distance?
A.) 3.3.3.0
B.) 255.255.255.0
C.) 4.4.4.4
D.) route
E.) 125 | | 2 |
| As a system administrator, you want to debug igrp but are
worried that the "debug IP igrp transaction" command will
flood the console. What is the command that you should
use?
A. debug IP igrp event
B. debug IP igrp-events
C. debug IP igrp summary
D. debug IP igrp events | | 1 |
| What is the IP extended access list range?
A.) 1000-1099
B.) 100-199
C.) 1-99
D.) 101-200 | | 2 |
| What is the command to start IP RIP version 1 routing on a
Cisco router?
A. show rip
B. enable rip
C. router enable
D. router rip | | 5 |
| what is the purpose of multicast packets? | | 1 |
| Your Ethernet interface currently has the IP address of
1.1.1.1/24. You would like it to have a second IP address of
2.2.2.2/24.
Which command will do that?
A.) ip address 1.1.1.1 2.2.2.2 255.255.255.0
B.) ip address 2.2.2.2 255.255.255.0 secondary
C.) ip address 2.2.2.2 255.255.255.0
D.) This cannot be done, you can only have 1 IP address per
physical
interface.
E.) ip address 2.2.2.2 /24 | | 1 |
| Which is true regarding half duplex Ethernet operation?
A.) Half Duplex ethernet technology provides a transmit circuit
connection wired directly to the receiver circuit at the
other end
B.) Half duplex transmission between stations is achieved by
using point
to multipoint Ethernet and Fast Ethernet
C.) With Half Duplex transmission logically circuits feed
into a single
cable creating a situation similar to a one way bridge
D.) Half Duplex transmission between stations is achieved
using Point to
Point Ethernet & Fast Ethernet | | 1 |
| What are the 3 ways routers learn paths to destination networks?
A.) Dynamic
B.) Static
C.) Routing tables
D.) Default | | 1 |
| Identify the 2 commands that will display the status and
information about interface E0 only?
A.) show interface ethernet E0
B.) show interface E0
C.) show E0
D.) show int E0
E.) show interface | | 1 |
| What is the syntax to add a banner to the Cisco router?
A.) motd banner #
B.) banner
C.) banner motd #
D.) banner # | | 1 |
| how we can creat VPN..??? how it can be configured on cisco
switches..??? can we creat VPN on different networks..???
why we need to create VPN..??? kindly write complete
activity of commands to configure a VPN on switch..??? me
specially looking towards Jatendra and Shahin | | 1 |
| Novell IPX network addresses have two conferrable parts.
The network administrator specifies the IPX network number.
How is the node number determined?
A. It is the serial number of the given device
B. It is assigned as a lease by Novell DHCP
C. It is also set by the network administrator
D. It is usually the MAC address of one Interface
E. It is downloaded by Netware Core Protocol (NCP) | | 1 |
| What is the difference between RIP & RIPng????
Can anyone explain it..!!!
Thank u in advance. | | 1 |
| Which layer is responsible for putting 1s and 0s into a logical
group?
A.) Session
B.) Application
C.) Transport
D.) Data Link
E.) Physical
F.) Network | | 2 |
| Identify the true statements about the following access list:
Access-list 101 deny tcp 192.10.172.0 0.0.0.255 any eq 23
Access-list 101 permit ip any any
A.) This access list prevents the host 192.10.172.0 from
telneting
B.) This access list prevents any telnet traffic from subnet
192.10.172.0/24
C.) This access list filters some telnet access
D.) This access list denies any telnet traffic to subnet
192.10.172.0/24
E.) This access list is invalid
F.) The netmask on the this access list is reversed | | 1 |
| Bridges work at what layer of the OSI model?
A.) Data Link
B.) Network
C.) Physical
D.) Application | | 2 |
| |
| For more CCNA Interview Questions Click Here |
along with your userid / name. ThanQ
Site Map
