Which layer is responsible for routing through an internetwork? A.) Phys

Advertise your Business Here

Refer this Site

Login | Sign Up


	Did you received any Funny E-Mails from your Friends and like to share with rest of our friends? Yeah!! you can post that stuff HERE

Categories >> Certifications >> Cisco Certifications >> CCNA

CCNA Interview Questions

CCDA Interview Questions

Question

Which layer is responsible for routing through an internetwork?

A.) Physical

B.) Session

C.) Network

D.) Transport

E.) Application

F.) Data Link

Question Submitted By :: Guest

I also faced this Question!!

Rank

Answer Posted By

Re: Which layer is responsible for routing through an internetwork? A.) Physical B.) Session C.) Network D.) Transport E.) Application F.) Data Link

Answer
# 1

Answer: C

The Network layer is responsible for routing. This is the
primary job of

routers, which operate at the Network layer.

Is This Answer Correct ?

2 Yes

0 No

Guest

Question	Asked @	Answers
Other CCNA Interview Questions


What does the acronym ARP stand for? A.) Address Resolution Phase B.) ARP Resolution Protocol C.) Address Resolution Protocol D.) Address Recall Protocol		1
Identify the type of routing protocol that exchanges entire routing tables at regular intervals? A.) Link state B.) Interior gateway protocols C.) Appletalk routing D.) Distance vector		1
How does inter- VLAN communication take place? A. It takes place through any Cisco router B. It takes place through a Cisco router that can run ISL C. It takes place through a router but this disables all the router a security and filtering functionality for the VLANS D. For nonroutable protocals (e.g. NetBeui) the router provides communications between VLAN domains E. Inter-VLAN communication is not possible because each VLAN is a separate broadcast domain		3
To prevent Service Advertisements (SAPs) from flooding a network, Cisco routers do not forward them. How are services advertised to other networks? A. Each router builds its own SAP table and forwards that every 60 seconds. B. Each router assigns a service number and broadcasts that. C. SAPs aren't necessary with Cisco routers. D. Cisco routers filter out all SAPs.		1
Which 2 commands shows the Cisco IOS filename? A.) show IOS B.) show ver C.) show flash D.) show mem E.) show NVRAM		1
The "ipx delay number" command will allow an administrator to change the default settings. What are the default settings? A. For LAN interfaces, one tick; for WAN interfaces, six ticks B. For LAN interfaces, six ticks; for WAN interfaces, one tick C. For LAN interfaces, zero ticks; for WAN interfaces, five ticks D. For LAN interfaces, five ticks; for WAN interfaces, zero Ticks		1
Identify the command mode necessary to enter the standard ping command? A.) Router(config)# B.) Router> C.) Router(std-ping)# D.) Router(config-if)#		2
what is the purpose of multicast packets?		1
Identify the keystroke used to terminate the setup mode? A.) Ctrl-K B.) Crtl-C C.) Ctrl-Z D.) Crtl-End		1
A traffic light is an example of what type of mechanism? A.) Collision detection B.) Flow control C.) Sequence numbering D.) Network management		1
What is the routing metric used by RIP? A.) Route poisoning B.) Split horizon C.) Hop Count D.) TTL		2
What is an example of a valid MAC address? A. 192.201.63.251 B. 19-22-01-63-25 C. 0000.1234.FEGA D. 00.00.12.34.FE.AA	Aricent	3
What are hold-downs used for? A.) To prevent regular update messages from reinstating a route that has come back up B.) Information received on an interface cannot be sent back out the same interface C.) To prevent regular update messages from reinstating a route that has gone down D.) To hold the routing table from being sent to another router		1
Which EXEC command displays system hardwarde configuration information software version and the names and sources of configuration files and boot images on a router? A. show boot B. show flash C. show config D. show version		1
Identify the access-list range for an extended IP access-list? A.) 800 - 899 B.) 1 - 99 C.) 1000 - 1099 D.) 100 - 199		4
Which range of possible numbers do standard ipx access lists have? A. 100 199 B. 600 699 C. 800 899 D. 1000-1099		1
Which of the following describe SMTP? A.) Used for downloading files to the router. B.) Used for sending e-mail. C.) Uses TCP. D.) Uses UDP. E.) Uses port 25. F.) Used for managing IP devices.		1
An ISDN BRI circuit can be described as which of the following? A.) 3B channels B.) 2-64Kbps B channels and 1-16Kbps D channel C.) none of the above D.) 2-64Kbps B channels and 1-16Kbps C channel		1
Which of the following are examples of the Application Layer? A.) LLC B.) Token Ring C.) Spreadsheet D.) TCP E.) IP F.) Word Processor		1
What is the default LMI type for Cisco Routers that are using Frame-Relay? A.) Gandalf5 B.) Q933A C.) Cisco D.) IETF E.) ARPA F.) SAP		2

For more CCNA Interview Questions Click Here


Copyright Policy \| Terms of Service \| Help \| Site Map 1 \| Articles \| Site Map \| Site Map \| Contact Us \|

Copyright © 2007 ALLInterview.com. All Rights Reserved.

ALLInterview.com :: Forum9.com :: KalAajKal.com