Which of the following describe full-duplex transmission? A.) Uses a sin

Advertise your Business Here

Refer this Site

Login | Sign Up


	SiteMap shows list of All Categories in this site.

Categories >> Certifications >> Cisco Certifications >> CCNA

CCNA Interview Questions

CCDA Interview Questions

Question

Which of the following describe full-duplex transmission?

A.) Uses a single wire

B.) Data transmission in only both directions, but only one
way at a time

C.) Uses a point-to-point connection from the transmitter of the

transmitting station to the receiver of the receiving station

D.) Data transmission in only one direction

Question Submitted By :: Guest

I also faced this Question!!

Rank

Answer Posted By

Re: Which of the following describe full-duplex transmission? A.) Uses a single wire B.) Data transmission in only both directions, but only one way at a time C.) Uses a point-to-point connection from the transmitter of the transmitting station to the receiver of the receiving station D.) Data transmission in only one direction

Answer
# 1

Answer: C

Full Duplex - Capability for simultaneous data transmission
between a

sending station and a receiving station. It requires a
workstation be

attached to a switch, the NIC must support it, and collision
detection

and loopback must be disabled.

Is This Answer Correct ?

0 Yes

1 No

Guest

Question	Asked @	Answers
Other CCNA Interview Questions


In IOS boot sequence if the flash is erased, and there is no access to TFTP server, and we can't load the partial IOS from ROM. Is there any possiblity that we can still boot the router/switch from external PC in which the IOS is installed?		5
Which of the following is a layer 2 device? A.) Switch B.) Bridge C.) Repeater D.) Hub		2
what is the binary value of loop back address		11
Identify the true statement regarding subnetting? A.) Allows for more host address B.) Borrow bits from the network portion of the address C.) Allows for unlimited number of networks D.) Borrow bits from the host portion of the address		1
Identify the command to display the Frame Relay map table? A.) Router# display frame-relay map B.) Router# show frame-relay map C.) Router(setup)# show frame-relay map D.) Router# show map frame-relay		1
Identify 2 HDLC characteristics? A.) Default serial encapsulation B.) Open standard C.) Supports Stacker compression D.) Supports point-to-point and multipoint		1
What is the protocol and what is the purpose of the following address? 238 255 255 255 A. IPX a SAP broadcast B. IP a multicast group C. IP a reserved address D. IP a directed broadcast E. IPX a flooded broadcast		2
what is frame relay?		8
Which OSI layer provides best effort end to end packet delivery? A.) Data-Link B.) Presentation C.) Network D.) Transport E.) Physical F.) Application		1
A traffic light is an example of what type of mechanism? A.) Collision detection B.) Flow control C.) Sequence numbering D.) Network management		1
Select the most correct statement regarding client port address assignment. The client port always matches the destination port. To access a web page the client uses the source port of 80 and the destination port is dynamically selected. When a client requests a web page the destination port is 80 by default and the source port for the client is dynamically selected. The client source port is 1024 to get web pages and 1055 when retrieving ftp files.		2
Which element is used to define the rate in bits per second that a Frame Relay switch agrees to transfer data? A. clock rate (CP) B. Committed Information Rate (CIR) C. Local Management Interface (LMI) D. data link connection identifier (DICI) E. Committed Rate Measurement Intercal (CRIMI)		1
Identify 3 Fast Ethernet technologies? A.) 100 Base FastEther B.) 100 Base FX C.) 100 Base T4 D.) 100 Base TX		1
When a router knows the IP address, but does not know the MAC address of the device it wishes to contact, it uses the ARP (Address resolution protocol) to determine the MAC address. After it learns the MAC address, it stores this information in the ARP cache. What is the command to view the ARP cache? A.) sh mac B.) show cache C.) show arp D.) sh arp interfaces E.) show ip cache		2
What are the Timer of RIP, IGRP, EIGRP and OSPF Routing Protocol?	IBM	15
What are 3 ways to provide login access to router? A.) Console B.) TFTP C.) Rlogin D.) Auxiliary Port E.) X Windows F.) Telnet		1
With one method for transmitting frames through a switch, the switch receives the complete frame and checks the frame CRC before forwarding the frame. What is the switch transmission method called? A. CSMA/CD B. Full Duplex C. Cut-Through D. Half-Duplex E. Fragmentation F. Store and Forward		2
Which of the following statements are true? A.) Store and forward switching creates variable latency through the switch B.) Cut through switching creates variables latency through the switch C.) Cut through switching works at wire speed D.) Store and forward switching works at wire speed		1
What is the default interval for SAP updates? A.) 60 seconds B.) 15 seconds C.) 30 seconds D.) 120 seconds	ACS	1
Identify 2 PPP characteristics? A.) Is proprietary to Cisco B.) Supports authentication C.) Support compression D.) Run on a multi-access network		2

For more CCNA Interview Questions Click Here


Copyright Policy \| Terms of Service \| Help \| Site Map 1 \| Articles \| Site Map \| Site Map \| Contact Us \|

Copyright © 2007 ALLInterview.com. All Rights Reserved.

ALLInterview.com :: Forum9.com :: KalAajKal.com