| Other CCNA Interview Questions |
| |
| Question | Asked @ | Answers |
| |
| What is LSA? How many types of LSA used by OSPF version 2?? | Hathway | 2 |
| Which protocol is used for booting diskless workstations?
A.) IP
B.) ARP
C.) RARP
D.) TCP
E.) SNMP | | 1 |
| Which three devices can be used to convert the user data
from the
DTE into a form acceptable to the WAN service's facility?
A. Modem
B. CSU/DSU
C. TA/NT1
D. CO
E. SS7 | | 1 |
| Which command displays the intenances using a given access list?
A. show filters
B. show ip interface
C. show active lists
D. show interface paramaters
E. configure ip access lists
F. show access-list interfaces | | 1 |
| MIDI and MPEG are examples of what layer of the OSI seven layer
model?
A.) Session
B.) Network
C.) Datalink
D.) Transport
E.) Application
F.) Presentation | | 1 |
| Identify the 2 commands that save the running-config to a TFTP
server?
A.) write running tftp
B.) copy running network
C.) copy running tftp
D.) write network | | 1 |
| Hi, All
I am configuring EIGRP in Packet tracer, after configuring
all the things it is not working but in one condition it is
working fine if i am putting all my router and network
withing one network subnets e.g. 172.16.0.0 or 10.0.0.0 but
whenever i am puting different network subnets e.g. in one
network it is RA(config-if)#=ip address 10.0.0.1, and in
fa0/0= 192.168.1.10 and in RB(config-if)#10.0.0.2 (s1/0) and
in S1/1 11.0.0.1 and in fa 0/0 192.168.100.1 ,where as in
third router RC(config-if)#=ip address 11.0.0.2 and in fa
0/0 172.16.1.10 and after configuring all this serial is
showing up and protocol showing up but eigrp process not
taking place after adding eigrp configuration, i tried with
"no auto-summary" command but not working.. Suggest me where
i missing something? can mail me at : gtech.innovator@gmail.com | | 18 |
| Identify the 3 key features of the Cisco Discovery Protocol?
A.) Off by default
B.) Will allow for the discovery of layer 3 addresses on
neighbor routers
C.) Verifies connectivity
D.) Open standard
E.) Does not require any layer 3 protocols to be configured | | 1 |
| Which service uses telephone control messages and signals
between
the transfer points along the way to the called destination?
A. Signaling System 7 (SS7)
B. Time-division Multiplexing (TDM)
C. X.25
D. Frame relay | | 1 |
| Which of the following describe full-duplex transmission?
A.) Uses a single wire
B.) Data transmission in only both directions, but only one
way at a time
C.) Uses a point-to-point connection from the transmitter of the
transmitting station to the receiver of the receiving station
D.) Data transmission in only one direction | | 1 |
| Identify the 2 commands the saves the running-config to NVRAM?
A.) write memory
B.) copy running-config startup-config
C.) write network
D.) write backup | | 1 |
| Identify the switching method that examines the destination MAC
address as the frame is being received then begins
forwarding the frame
prior to receiving the entire frame?
A.) Fragment-free
B.) Store and Forward
C.) Cut-through
D.) Fast forward | | 1 |
| Which of the following is an example of the Network Layer?
A.) TCP
B.) IP
C.) SQL
D.) Token Ring
E.) LLC | | 1 |
| Identify 3 LAN technologies?
A.) FDDI
B.) HDLC
C.) HSSI
D.) X.25
E.) 802.3
F.) 802.5 | | 1 |
| Which of the follwing are true of standard half-duplex
Ethernet circuitry?
A. It is alternate one-way communication
B. The receive (RX) is wired directly to the transmit (TX)
of the remote station
C. The transmit (TX) is wired directly to the receive (RX)
of the remote station
D. Collisions are not possible
E. Both stations can transmit simultaneously | | 1 |
| Identify the prompt displayed if in privileged exec mode?
A.) Router(config)#
B.) Router#
C.) Router>
D.) Router(priv)# | | 1 |
| mention the funtions about connection oriented and
connectionless protocol and how it works ? | | 4 |
| A company running RIP V1 protocol on their 2 seperate
networks, each nw has 14 routers, if the two nw wants to be
merged with each other total no of routers will be 28. but
rip metric is hop count(15). What needs to be done if this
setup needs to be work ? | Satyam | 2 |
| Which two statements about the store and forward switching
method are true? (Choose two)
A. Latency remains constant regardless of frame size.
B. Latency through the switch varies with frame length.
C. The switch receives the complete frame before forwarding it.
D. The switch checks the destination address as soon as it
receives the header and begins forwarding the fram immediately. | | 1 |
| Why we choose the router rather then L-3 Switch | Network-Solutions | 7 |
| |
| For more CCNA Interview Questions Click Here |
Site Map
