| Other CCNA Interview Questions |
| |
| Question | Asked @ | Answers |
| |
| Identify the 3 methods routers learn paths to destinations?
A.) Dynamic routing
B.) None of the above, configured by default
C.) Default routes
D.) Administrative distance
E.) Static routes | | 1 |
| Identify the 2 rules used when configuring a Distance Vector
routing protocol?
A.) Physically connected network(s)
B.) Configure the classful address, no subnets
C.) Enable CDP so neighbors can be detected
D.) Configure all networks in Area0 | | 1 |
| Which layer is responsible for providing mechanisms for
multiplexing
upper-layer application, session establishment, and tear
down of virtual
circuits?
A.) Session
B.) Network
C.) Physical
D.) Transport
E.) Application
F.) Presentation | | 1 |
| Identify the command to configure ALL the default VTY ports?
A.) Router(config)# line vty 0 4
B.) Router# line vty 0 4
C.) Router(config)# line vty
D.) Router(config)# line vty 0 | | 2 |
| Which commands should you use to enable IGRP routing?
A. router igrp 100
Network 192.168.1.0
Network 10.0.0.0
B. router igrp 100
Network 192.168.2.0
Network 10.0.0.0
C. router igrp 100
Network 192.168.1.0 192 168.1.1
Network 10.2.0.0 10.2.1.1
D. router igrp 100
Network 192.168.1.0 255.255.255.0
Network 10.2.0.0 255.255.255.0 | | 2 |
| Your PC has been configured with IP Address 192.168.3.25
and a subnet mask of 255.255.255.0. Which of the following
IP Addresses is a valid default gateway address for your
PC?
192.168.3.0 255.255.255.0
192.168.3.2 255.255.255.0
192.168.3.25 255.255.255.0
192.168.4.1 255.255.255.255
| | 1 |
| Which feature of PPP (Point to Point Protocol) allows the router
to bind multiple channels together, to form a single logical
channel?
A.) multi-link ppp
B.) multi-channel ppp
C.) can't be done
D.) omni-ppp
E.) plp | | 1 |
| Which of the following is a valid TCP/IP socket for an
Email connection?
101.34.2.125:25
00-00-03-1B-CA-6F:143
202.167.23.101:21
60.4:110
| | 1 |
| Identify the command to configure the IP address 172.16.100.5
255.255.255.0?
A.) Router(config-if)# ip address 172.16.100.5 255.255.255.0
B.) Router(config)# ip address 172.16.100.5
C.) Router# ip address 172.16.100.5 255.255.255.0
D.) Router(config)# ip address 172.16.100.5 255.255.255.0 | | 2 |
| What is the difference between DTE & DCE??? | | 5 |
| What are the two primary operating modes for frame switching?
A. Full Duplex
B. Half-Duplex
C. CSMA/CD
D. Cut-through
E. Fragmentation
F. Store and Forward
G. User mode
H. Privileged mode | | 1 |
| What does the IPX maximum path command do?
A.) Allows you to disable the TTL on an IPX packet
B.) This parameter is only used in NLSP routing
C.) Sets the maximum metric that can appear in the routing table
D.) Configures round robin load sharing over multiple equal
metric paths
(parallel paths) | | 1 |
| What does the term Base refer to in 100BaseT
A. cabling type
B. singnal type
C. 100 mode type
D. spectrum used
E. speed category | | 2 |
| What is Spanning Tree Protocol and how it work? I know it
is - STP is Spanning tree Protocol. It Stops the looping in
the network? How STP work? How it stop Looping in network? | | 2 |
| The -- terminal no editing -- command will perform what
function?
A.) Edit the contents of NVRAM
B.) Allows access to the terminal port
C.) Stops the advanced editing feature
D.) Enable password functions | | 1 |
| What does a metric of 16 hops represent when using RIP?
A.) Number of hops to the destination
B.) Destination unreachable
C.) Number of routers
D.) Bandwidth | IBM | 2 |
| What is the standard ISDN term for a non-native analog
telephone?
A.) TE1
B.) TA
C.) LE
D.) TE2
E.) ET | | 1 |
| How often does IP RIP send out routing table updates by default?
A.) They send complete updates every 30 seconds
B.) They send partial updates every 30 seconds
C.) They send complete updates every 60 seconds
D.) They send partial updates every 60 seconds | | 2 |
| "snap" is used by the Cisco IOS for which encapsulation
types?
A. Ethernet_SNAP
B. Token-Ring_SNAP
C. FDDI_SNAP
D. Novell-SNAP
E. Novell-FDDI. | | 1 |
| Which layer is responsible for putting 1s and 0s into a logical
group?
A.) Session
B.) Application
C.) Transport
D.) Data Link
E.) Physical
F.) Network | | 2 |
| |
| For more CCNA Interview Questions Click Here |
Site Map
