| Other CCNA Interview Questions |
| |
| Question | Asked @ | Answers |
| |
| Identify the prompt displayed if in privileged exec mode?
A.) Router(config)#
B.) Router#
C.) Router>
D.) Router(priv)# | | 1 |
| Which of the following protocols are used for logical network
addressing?
A.) IP
B.) TCP
C.) ARP
D.) ICMP
E.) RARP
F.) BootP | | 1 |
| What are 3 ways to provide login access to router?
A.) Console
B.) TFTP
C.) Rlogin
D.) Auxiliary Port
E.) X Windows
F.) Telnet | | 1 |
| The following selections show the command prompt and the
configuration of the IP network mask. Which two are
correct?
A. Router#term IP netmask-format { bitcount | decimal |
hexadecimal }
B. Router(config-if)#IP netmask-format { bitcount | decimal
| hexadecimal }
C. Router(config-if)#netmask-format { bitcount | decimal |
hexadecimal }
D. Router#ip netmask-format { bitcount | decimal | hexadecimal } | | 1 |
| The following is partial output from a routing table ;
'192.168.10.0 [100/1300] via 10.1.0.1, 00:00:23, Ethernet1'
Which routing protocol is being used? (assuming defaults
have not been
changed)
A.) OSPF
B.) RIP
C.) BGP
D.) IGRP | | 1 |
| In regards to TCP/IP, which class of address allows for the
fewest
valid
Internet hosts?
A.) D
B.) E
C.) Classes are not used in TCP/IP.
D.) B
E.) C
F.) A | | 1 |
| Which frame has a Type field to identify the upper-layer
protocol?
A.) 802.3
B.) 802.2
C.) 802.5
D.) Ethernet_II | | 1 |
| What is the syntax to use to configure the port on a
Catalyst 5000
switch?
A.) slot port/type
B.) type slot/port
C.) port slot/type
D.) port type/slot | | 2 |
| Choose three reasons why the networking industry uses a layered
model:
A.) It facilitates systematic troubleshooting
B.) It allows changes in one layer to occur without changing
other layers
C.) It allows changes to occur in all layers when changing
one protocol
D.) It clarifies how to do it rather than what general
function to be done
E.) It clarifies what general function is to be done rather
than how to
do it | | 1 |
| What would be the first command from global configuration
mode to
enable
RIP on your router for interface E0, with an address of
181.86.4.4 and
mask of 255.255.255.0 ?
A.) router rip
B.) network 181.89.4.0 255.255.255.0
C.) router rip int e0
D.) router rip 181.86.0.0
E.) router rip 181.86.4.0
F.) network 181.86.0.0 | | 1 |
| You just entered the following command_Router(config#) line
console 0 Which operation is most likely to follow?
A. Confound terminal type
B. enter protocol parameters for a serial line
C. create a password on the console terminal line
D. establish a terminal type 4 connection to a remote host
E. change from configuration mode to console privileged mode | Wipro | 10 |
| What is the result of segmenting a network with a router
into segments 1 and 2?
A. It increases the number of collisions
B. It decreases the number of broadcast domains
C. It connects segment 1 and broadcasts to segment 2
D. It connects segment 1 and broadcasts from genre to segment 2 | | 1 |
| What command would show the version of the IOS that you are
running?
A.) show nvram
B.) show version
C.) show startup-config
D.) show ios
E.) ver -a
F.) show ram | | 1 |
| There are 2 types of PPP authentication supported by the Cisco
IOS. What
are they?
A.) PAP
B.) PREDICTOR
C.) MD5
D.) CHAP
E.) STACKER
F.) MSCHAP | | 4 |
| What is the syntax to add a banner to the Cisco router?
A.) motd banner #
B.) banner
C.) banner motd #
D.) banner # | | 1 |
| What is the regional telco office called, where the customers
local loop terminates?
A.) Demarc
B.) DTE
C.) DCE
D.) CO
E.) CPE | | 1 |
| Identify the access-list range for an extended IP access-list?
A.) 800 - 899
B.) 1 - 99
C.) 1000 - 1099
D.) 100 - 199 | | 1 |
| What 3 sources can configuration commands be placed into RAM?
A.) HP Openview
B.) Console
C.) Vterminal
D.) TFTP server
E.) NVRAM | | 1 |
| what is difference between
1 pap and chap(quite easy but need on line answer)
2 chap and ms-chap(plz describe briefly)
now i have posted the question is there any one to help me?
| | 1 |
| Identify the prompt displayed if in privileged exec mode?
A.) Router(config)#
B.) Router#
C.) Router>
D.) Router(priv)# | | 1 |
| |
| For more CCNA Interview Questions Click Here |
Did you received any Funny E-Mails from your Friends and like to share with rest of our friends? Yeah!! you can post that stuff 
Site Map
