| Other CCNA Interview Questions |
| |
| Question | Asked @ | Answers |
| |
| Hello Mr.Jitendera Kuamr Sinha, how is every thing going
on? Thanks for your reply. Dear Friend if you can Explain
it little bit deeper i will be realy thanks full. Wish you
all the Best.
| | 1 |
| Which element is used to define the rate in bits per second
that a Frame Relay switch agrees to transfer data?
A. clock rate (CP)
B. Committed Information Rate (CIR)
C. Local Management Interface (LMI)
D. data link connection identifier (DICI)
E. Committed Rate Measurement Intercal (CRIMI) | | 1 |
| What does CCNA stand for?
A. Cisco Certified Network Administrator
B. Cisco Certified Network Associate
C. Certified Circuitry in Networking Apprentice
D. Calico Cats of North America | | 3 |
| What does the Frame Relay switch use to distinguish between
each PVC connection?
A. data-link connection identifiers (DLCIs)
B. BECNs
C. FECNs
D. the Local Management Interface (LMI) | | 2 |
| Identify the 2 commands that will display the status and
information about interface E0 only?
A.) show interface ethernet E0
B.) show interface E0
C.) show E0
D.) show int E0
E.) show interface | | 1 |
| Identify the components in the following command 'interface
serial0/1/1'
A.) Serial interface, port number 0, slot 1, port adapter 1
B.) Serial interface, slot 1, port number 1, port adapter 0
C.) Serial interface, slot 0, port adapter 1, port number 1 | | 1 |
| Identify the command to determine if CDP is enabled?
A.) show enable cdp
B.) show cdp enabled
C.) show cdp run
D.) show cdp | | 2 |
| Why would you use static routing instead of dynamic routing?
A.) When you want automatic updates of the routing tables
B.) All the time
C.) When you have very few routes and want to conserve bandwidth
D.) When you have a gateway of last resort | | 1 |
| Request any body to explain the parameters of Ipsec vpn
tunnel while creating a tunnel in Cisco ASA. | HCL | 3 |
| The maximum distance on a 10BaseT network from the hub to a
workstation is
which of the following?
A.) 500 meters
B.) 1000 meters
C.) 100 meters
D.) 1500 meters | | 1 |
| The benefits to segmenting with Bridges are which of the
following?
A.) Scalability
B.) Datagram filtering
C.) Manageability
D.) Reliability | | 1 |
| A ISDN PRI circuit can be described as which of the following?
A.) 24 B channels and 1-64Kbps D channel
B.) 23 B channels and 1-64Kbps D channel
C.) 2-D channels and 1-C channel
D.) 2-64Kbps B channels and 1-16Kbps D channel | | 1 |
| Given an IPX network with redundant paths, what command will
configure load balancing?
A.) ipx load-balance
B.) ip maximum-paths 2
C.) ipx maximum-paths 2
D.) ipx load-share | | 1 |
| What is the difference between OSPF Exteral Type 1 (O E1) &
External Type 2 (O E2) routes???? | | 3 |
| Identify the 3 characteristics of IGRP?
A.) Uses hop count as a metric
B.) Supports multiple unequal paths
C.) Administrative distance is 100
D.) Configured with an Autonomous system number
E.) Link state | | 1 |
| What are the 2 functions of the Data Link Mac layer?
A.) Handles access to shared media
B.) Manages protocol access to the physical network medium
C.) Provides SAPs for higher level protocols
D.) Allows multiple devices to uniquely identify one another
on the data
link layer | | 1 |
| How Bridge Protocol Data Unit detect looping in Network?
How Bridge Protocol Data Unit work? explain? | | 1 |
| Identify 2 features of X.25?
A.) Supports only IP
B.) Utilizes switched and permanent virtual circuits
C.) Contains minimal flow control and error recovery
D.) Utilizes LAPB as it's data-link protocol | | 1 |
| What does the IPX maximum-path command do?
A.) Allows you to disable the TTL on an IPX packet
B.) This parameter is only used in NLSP routing
C.) Sets the maximum metric that can appear in the routing table
D.) Configures round robin load sharing over multiple equal
metric paths
(parallel paths) | | 1 |
| What is the function of Layer 2 Switch? | | 1 |
| |
| For more CCNA Interview Questions Click Here |
along with your userid / name. ThanQ
Site Map
