What's the default CDP holdtime in seconds for Cisco routers? A.) 3

Advertise your Business Here

Refer this Site

Login | Sign Up


	To Refer this Site to Your Friends Click Here

Categories >> Certifications >> Cisco Certifications >> CCNA

CCNA Interview Questions

CCDA Interview Questions

Question

What's the default CDP holdtime in seconds for Cisco routers?

A.) 30 seconds

B.) 180 seconds

C.) 90 seconds

D.) 60 seconds

Question Submitted By :: Guest

I also faced this Question!!

Rank

Answer Posted By

Re: What's the default CDP holdtime in seconds for Cisco routers? A.) 30 seconds B.) 180 seconds C.) 90 seconds D.) 60 seconds

Answer
# 1

Answer: B

Cisco Discovery Protocol is a proprietary protocol to allow
you to

access configuration information on other routers and
switches with a

single command. It uses SNAP at the Data-Link Layer. By
default CDP

sends out a broadcast every 60 seconds and it holds this
information for

180 seconds. CDP is enabled by default.

Is This Answer Correct ?

1 Yes

0 No

Guest

Re: What's the default CDP holdtime in seconds for Cisco routers? A.) 30 seconds B.) 180 seconds C.) 90 seconds D.) 60 seconds

Answer
# 2

Is This Answer Correct ?

1 Yes

0 No

Basheer Shafi

Question	Asked @	Answers
Other CCNA Interview Questions


You have powered on a new router and you want to create an initial configuration. Which mode should you use? A. copy mode B. user mode C. setup mode D. startup mode	Enrich	3
A big part of the overhead on a network is broadcasts. You divide a large number of hosts into smaller individual networks and separate them with the proper device According to proper networking terminology you have created separate _______________________, User Domains Broadcast Domains Collision Areas Broadcast Areas		1
Identify the 3 pieces of hardware you would not install to prevent broadcasts? A.) Switch B.) Repeater C.) Bridge D.) Router		2
Identify 3 IP routing protocols? A.) RIP B.) AURP C.) OSPF D.) IGRP E.) ARP F.) ICMP		2
When would you use ISDN? A.) To connect LANs using POTS B.) To support applications requiring voice, data, and video C.) When you need a consistent and very high rate of data speed D.) To connect to IBM mainframes		1
Choose the following that are benefits to segmenting with router: A.) Flow Control B.) Manageability C.) Multiple Active Paths D.) Explicit packet lifetime control		1
why we give clock rate to DCE and not to DTE what is the difference in the two.		2
Eight stations connected to separate 10 Mobs pods on a Layer 2 switch will give each station how many Mobs of bandwidth? A. 1.25 B. 4 C. 16 D. 10 E. 80		1
Identify the OSI layer responsible for end-to-end connections? A.) Network B.) Transport C.) Session D.) Data link E.) TCP		1
What are four benefits that can result from applying ISDN networking? (Choose four) A. Full time connectivity across the ISDN is spoofed by Cisco IOS routers using dial on demand routing (DDR) B. Small Once and Home Once sites can be economically supported with ISDN Basic Rate Interface (BRI) servkps C. ISDN replaces Signaling System 7 (SS7) in the Public Switched Telephone Network (PSTIC) backbone D. ISDN can be used as a backup service for a leased line connection between the remote and central chaps E. Modem racking and cabling can be eliminated by integration of digital modem cards on Cisco IOS Network Acess Servers (NAS)		2
Routers that have Flash memory typically have a ore loaded copy of place IOS software. Which command should you use to make a backup copy of the software image onto a given network server? A. copy flash tftp B. save copy to tftp C. write backup tftp D. write, backup -server-name- E. copy backup to -server-name-		1
Identify the purpose of ICMP? A.) Avoiding routing loops B.) Send error and control messages C.) Transporting routing updates D.) Collision detection	Hughes	2
What is true about frame-relay DLCI? A.) DLCI represents a single physical circuit B.) DLCI is optional in all frame-relay networks C.) DLCI identifies a logical connection between DTE devices D.) DLCI is used to tag the beginning of a frame with VLAN information		1
What is a backoff on an 802.3 networks A. It is latency in store and forward switching B. It is the time used for token passing from machine to machine C. It is the retransmission delay that is enforced when a collision occurs D. it is the result of two nodes transmitting at the same time. The frames from each transmitting device collide and are damaged.		3
Which three types of connectors are commonly associated with Cisco's V.35 serial cables? (Choose three.) 0 RJ 11 1 DB 60 2 Winchester 15 pin 3 DB 9 4 smart serial 5 RJ 45		3
Routers can learn about destinations through static routes, default, or dynamic routing. By default, a router will use information derived from __________. A. IGRP B. RIP C. IP D. TCP	pspl	2
Which of the following will apply IPX sap access list 1010 for incoming traffic, assume you are at the interface configuration? A.) ipx input-sap-filter 1010 in B.) ipx input-sap-filter 1010 C.) ipx access-group 1010 in D.) ipx access-list 1010 in		1
During encapsulation, in which order is information packaged? A. Data, Packet, Segment, Frame B. Segment, Data, Packet, Frame C. Data, Segment, Packet, Frame D. Packet, Data, Segment, Frame E. Frame, Data, Segment, Packet F. Bread, Peanut Butter, Jelly, Bread		2
What layer can optionally support reliability? A.) Transport B.) IP C.) Physical D.) Network E.) Sub-physical layer		1
What does 'P' mean when running a Trace? A.) Good route B.) Protocol unreachable C.) Source Quench D.) Destination unreachable		1

For more CCNA Interview Questions Click Here


Copyright Policy \| Terms of Service \| Help \| Site Map 1 \| Articles \| Site Map \| Site Map \| Contact Us \|

Copyright © 2007 ALLInterview.com. All Rights Reserved.

ALLInterview.com :: Forum9.com :: KalAajKal.com