| Other CCNA Interview Questions |
| |
| Question | Asked @ | Answers |
| |
| Identify the switching method that examines the destination MAC
address as
the frame is being received then begins forwarding the frame
prior to
receiving the entire frame?
A.) Fragment-free
B.) Store and Forward
C.) Cut-through
D.) Fast forward | | 1 |
| Which command line statement determines the number of seconds a
dialup connection can wait without any traffic before the
router hangs up?
A.) dialler max-time
B.) dialler timeout
C.) dialer idle-timeout
D.) dialer hang-up
E.) disconnect-timer | | 2 |
| Which of the following is true?
A. The default is to send debug output to the console screen.
B. To view debug output from a telnet session, the "terminal
monitor" command must be used
C. If the "logging buffered" command is used, the debug
output would be sent to RAM and can be viewed with the "show
log" command
D. If the "no console loggin" command were configured,
output would besent to a telnet session
E. All of the above
F. None of the above
G. A, B, and C.
H. A, C, D, and E. | | 2 |
| Identify the command to reload the router?
A.) Router(config)# reload
B.) Router# reset
C.) Router# reload
D.) Router> reload | | 1 |
| Which 2 commands shows the Cisco IOS filename?
A.) show IOS
B.) show ver
C.) show flash
D.) show mem
E.) show NVRAM | | 1 |
| What command can be used to test IPX connectivity?
A.) Ping 2e.000.0045.8923
B.) Ping 192.168.100.1
C.) Ping ipx 2e.0000.0045.8923
D.) Ipx ping 2e.0000.0045.8923 | | 3 |
| What is the default CDP broadcast update rate for Cisco routers?
A.) 120 seconds
B.) 60 seconds
C.) 30 seconds
D.) 90 seconds | | 1 |
| If you are in IOS user mode, which command do you use to
enter the privileged mode?
A. Set
B. Enable
C. Configure
D. Privileges | | 1 |
| Select the most correct statement regarding client port
address assignment.
The client port always matches the destination port.
To access a web page the client uses the source port of
80 and the destination port is dynamically selected.
When a client requests a web page the destination port
is 80 by default and the source port for the client is
dynamically selected.
The client source port is 1024 to get web pages and 1055
when retrieving ftp files.
| | 2 |
| Identify the named IP access-list number range?
A.) 600 - 699
B.) 1 - 99
C.) 900 - 999
D.) 200 - 299
E.) none of the above | | 2 |
| Which OSI Reference Layer is concerned with path determination?
A.) Datalink
B.) Physical
C.) Network
D.) Transport
E.) Session | | 2 |
| Which of the following are Transport layer protocols?
A.) UDP
B.) TCP
C.) NBP
D.) IP
E.) SPX | | 3 |
| Identify 3 characteristics of switches?
A.) Increase available bandwidth
B.) Decrease broadcast traffic
C.) Support full duplex in a multipoint topology
D.) Make forwarding decision using MAC address
E.) Create collision domains | | 1 |
| hi friend i hav difficulty n need to solve it...v need to
implement a new raw switch in company as to increase the no
of staff...snc raw switch by default is in server mode,i
wanna know 1.how to make a switch in client mode...2.how to
configure switch i mean to sy how to connect all switches to
network. | | 1 |
| We know that TCP provides connection oriented services, what
else
does it provide?
A.) FECN & BECN
B.) Path discovery.
C.) Flow control and error checking.
D.) Name resolution.
E.) File manipulation. | | 1 |
| Which OSI Reference Layer controls end-to-end (host to host)
communication?
A.) Transport
B.) Physical
C.) Datalink
D.) Network
E.) Session | | 1 |
| Which router command allows you to view the entire contents
of all access lists?
A. Router# show interface
B. Router> show ip interface
C. Router# show access-list
D. Router> show all access-list | | 2 |
| You have typed "ping" 172.16.101.1 and get the following
display:
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echoes to 172.16.101.1,
timeout is 2 seconds:
.!!!!
What does the "." signify?
A. That one message timed out.
B. That all messages were successful.
C. That one message was successful.
D. That one message completed in under the allotted
timeframe. | | 1 |
| What does the IPX maximum path command do?
A.) Allows you to disable the TTL on an IPX packet
B.) This parameter is only used in NLSP routing
C.) Sets the maximum metric that can appear in the routing table
D.) Configures round robin load sharing over multiple equal
metric paths
(parallel paths) | | 1 |
| You want a message to be displayed every time someone tries
to log
on to the router. Which command is required to accomplish
this task?
A.) motd#(message)#
B.) banner motd(message)
C.) banner motd#(message)#
D.) banner motd*(message)
E.) banner login#(message)# | | 1 |
| |
| For more CCNA Interview Questions Click Here |
Site Map
