| Other CCNA Interview Questions |
| |
| Question | Asked @ | Answers |
| |
| A router blocks ___________
Broadcasts
Unicasts
All packets
Nothing
| | 1 |
| Why would you use static routing instead of dynamic routing?
A.) When you want automatic updates of the routing tables
B.) All the time
C.) When you have very few routes and want to conserve bandwidth
D.) When you have a gateway of last resort | | 1 |
| 8. When is Frame Tagging used?
A. When you install repeaters in your network
B. When you install bridges in your network
C. When you install routers in your network
D. When you use Switches configured with multiple VLANS
| | 4 |
| Which command do you use to set the Privileged mode password to
'clearwater'?
A.) set password=clearwater
B.) enable privilege password clearwater
C.) enable password clearwater
D.) enable login clearwater
E.) enable secret password clearwater
F.) ebable clearwater | | 1 |
| here is your question sahin
Hi Jitendera, If i m not wrong, then in EIGRP, Metric weight
is set to K1(Bandwidth)=1, K2(Delay)=0, K3(Reliability)=1,
K4(Load)=0, K5(MTU)=0. This is default setting for EIGRP.
I knew about it from ICND 2 cisco press book.
Three more questions -
a) If we change the K value (I mean metric weight)on a
router what will happen???
b) When redistribution is necessary in EIGRP. Is there any
condition for that???
c) What is reference bandwidth for metric calculation in
EIGRP. As we know, in OSPF, on a CISCO router reference
bandwidth is 10Mbps. | | 3 |
| Which command displays the IPX SAP table?
A.) show ipx sap
B.) show sap
C.) show ipx interface
D.) show ipx servers
E.) show ipx | | 1 |
| When setting up a frame-relay network between a Cisco router
and a
non-Cisco router, what encapsulation type should you use?
A.) SAP
B.) CISCO
C.) IANA
D.) Apollo
E.) IETF
F.) Q933A | | 1 |
| Which command will display the encapsulation type on interface
serial 0?
A.) show interface s0
B.) show all
C.) show int s0 encap
D.) show encap s0
E.) show encap | | 1 |
| If you are running Token Ring with Novell IPX routing, which
encapsulation
should you use?
A.) SAP
B.) SNAP
C.) 802.5
D.) 802.2 | | 1 |
| What is the default bandwidth of a serial connection?
A.) 1200 baud
B.) 1.544 Mbps (T1)
C.) 10 Mbps
D.) 96Kpbs | | 1 |
| How many subnets can be gained by subnetting 172.17.32.0/23
into a /27 mask, and how many usable
host addresses will there be per subnet? | | 8 |
| what is burst rate | ASD-Lab | 1 |
| When discussing static routes, what is the gateway parameter
used
for?
A.) Determining the dynamic route
B.) Defining the subnet
C.) Defining the Administrative Distance
D.) Determining the next hop | | 1 |
| Your network is having IP problems connecting to one or more
Frame Relay peer routers. Which two commmands should you
use to show the routers that are reachable? (Choose two)
A. show ip map
B. show ip router
C. show frame-relay map
D. debug frame-relay map | | 1 |
| When using TCP, after a session is open, the applications
can adjust the amount of segments they receive before
sending an acknowledgment. This behaviour is known as
______________.
FCS
Windowing
MTU adjustment
Flexible Send Path
| | 1 |
| Scenario: You created 2 access-lists for controlling telnet
about
a year ago, and bound one of them to Serial 0. You can't
remember which
access-list you
used. Which command lets you see all access-lists on Serial
0 for telnet?
A.) show access-list
B.) show ip int s0
C.) show access-list telnet
D.) show telnet access-list
E.) show access-list s0
F.) show int s0 | | 2 |
| Which layer defines bit synchronization?
A.) Application
B.) Network
C.) Transport
D.) Physical
E.) Session
F.) Session | | 1 |
| In the command "router igrp 109" what does 109 signify?
A. an autonomous system
B. any network number which the router is attached to
C. the allowable length of the routing table
D. the network socket number | | 1 |
| Which layer is responsible for negotiating data transfer syntax?
A.) Network
B.) Session
C.) Application
D.) Transport
E.) Presentation | | 1 |
| Identify the command to configure DLCI 100 on an interface e0?
A.) Router(config)# frame-relay local-dlci 100
B.) Router(config)# frame-relay local-dlci 100 int e0
C.) Router(config-if)# frame-relay local-dlci 100
D.) Router(config-if)# frame-relay local-dlci 100 int e0 | | 1 |
| |
| For more CCNA Interview Questions Click Here |
Site Map
