| Other CCNA Interview Questions |
| |
| Question | Asked @ | Answers |
| |
| How does the cut-through switching technique work?
A.) By using broadcast address as source addresses
B.) The switch waits only for the header to be received
before it checks
the destination address and starts forwarding the packets
C.) The LAN switch copies the entire frame into its onboard
buffers and
then looks up the destination address in its forwarding, or
switching,
table and determines the outgoing interface
D.) By using a Class I repeater in a collision domain | | 3 |
| what is frame relay.and how it is different from isdn | HCL | 1 |
| what is 5-4-3 rule? | | 1 |
| What is the Difference between Switch and Bridge? | | 3 |
| IP standard access lists use which of the following as a
basis for
permitting or denying packets?
A.) destination address
B.) port
C.) protocol
D.) source address | | 1 |
| What does the command “IP name-server 255.255.255.255″
accomplish?
a.It disables domain name lookup.
b.It sets the domain name lookup to be a local broadcast.
c.This is an illegal command.
d.The command is now defunct and has been replaced by “IP
server-name ip any”
| | 5 |
| Which Distance Vector characteristic can help to speed up
convergence?
A.) Triggered Updates.
B.) Split Horizon.
C.) Poison Reverse.
D.) Hold Down timers.
E.) Inverse ARP. | | 1 |
| Which statement about switched and routed data flows is correct?
A. Switches create a single collision domain and a single
broadcast domain. Routers provide separate collision domains
B. Switches create separate collision domains but a single
broadcast domain. Routers provide a separate broadcast domain
C. Switches create a single collision domain and separate
broadcast domains. Routers provide a separate broadcast
domain as well
D. Switches create separate collision domains and separate
broadcast domains. Routers provide separate collision domains | | 1 |
| ok this is practical senario question
how can we comunicate two diffrent network host by i single
1603 sires of cisco router rember that the cisco series of
that router have singe 100mbps ethernet
now think think
write all command
answer is so simple i wiil; give the answer after 20 visit
til then wait
| | 2 |
| What is the juncture at which the CPE ends and the local loop
portion of the service begins?
A. Demarc
B. CO
C. Local loop
D. Last-mile | | 1 |
| why we give clock rate to DCE and not to DTE
what is the difference in the two. | | 2 |
| Dear Mr.Shahin thank you very much for your advise i realy
thanks full to you.
Best of luck | | 2 |
| Novell's implementation of RIP updates routing tables every
____ seconds.
A. 60
B. 90
C. 10
D. 30 | Wipro | 1 |
| 3. What does a bridge use to segment a network?
A. IP Addresses
B. Broadcasts
C. Application data
D. Media Access Control addresses
| | 2 |
| what is native vlan
any one explain
sooraj | | 2 |
| What’s the default CDP holdtime in seconds for Cisco routers?
| | 2 |
| What is an administrative distance of 0 mean?
A.) 0 means unbelievable
B.) 0 is for EIGRP
C.) 0 is the default distance for directly connected networks
D.) 0 means unreachable | | 1 |
| If you are in IOS user mode, which command do you use to
enter the privileged mode?
A. Set
B. Enable
C. Configure
D. Privileges | | 1 |
| What are four ways that Fast Ethernet compares to 10BaseT
Ethernet? (Choose four)
A. Fast Ethernet uses the same Maximum Transmission Unit (MTU)
B. Fast Ethernet is based on an extension to the IEEE 802.3
specification
C. Fast Ethernet uses the same Media Access Control (MAC)
mechanisms
D. Fast Ethernet preserves the frame format that is used by
10BaseT Ethernet
E. Fast Ethernet errors a speed increase one hundred times
that of the 10BaseT Ethernet | | 1 |
| what is the need og
jitu(config)#ip helper address <ip address>
can any one exaplain it briefly
specially shain i am looking towards you.Becoz you are the
only one who can solve my that problem not even jitendera sinha | | 3 |
| |
| For more CCNA Interview Questions Click Here |
Site Map
