| Other CCNA Interview Questions |
| |
| Question | Asked @ | Answers |
| |
| Describe End to End network services: (Choose all that apply)
A.) Best Route selection
B.) Accomplished Segment by Segment, each segment is autonomous
C.) Flow Control & Data Integrity
D.) Best efforts packet delivery | | 1 |
| What is VLSM? Why we Create? When we Create? Implement VLSM
with example? | | 4 |
| A default route is analogous to a _________.
A. default gateway
B. static route
C. dynamic route
D. one-way route | | 1 |
| Which commands would assign and enable IPX on an interface ?
A.) enable netware
B.) enable novell-ether
C.) router#(config)ipx routing
D.) You must first enable IPX globally and then
assign the network number to the interface .
E.) enable ipx
F.) router#(config-if)ipx network 4a | | 1 |
| What is the function of DDR on Cisco routers?
A. DDR is dial--on-demand routing. It provides a continuous
LAN only
connection.
B. DDR is dial-on-demand routing. It provides routing for
high volume
traffic.
C. DDR is dial--on-demand routing. It provides a continuous
WAN connection.
D. DDR is dial-on-demand routing. It provides routing for
low volume and
periodic traffic. | | 2 |
| Which addresses are INCORRECTLY paired with their class?
A. 128 to 191, Class B
B. 192 to 223 Class B
C. 128 to 191, Class C
D. 192 to 223, Class C | | 2 |
| Which protocol resolves an IP address to a MAC address?
A.) DHCP
B.) RARP
C.) ARP
D.) NBP
E.) DNS | | 3 |
| Layer 1 and Layer 2 devices must forward a broadcast.
Which of the following devices fall into this category?
Gateway
Switch
Router
All of the above.
| | 1 |
| Identify the command that displays the SAP table?
A.) show ipx servers
B.) display SAP table
C.) display SAP's
D.) show sap table | | 1 |
| Identify the 2 rules used when configuring a Distance Vector
routing
protocol?
A.) Physically connected network(s)
B.) Configure the classfull address, no subnets
C.) Enable CDP so neighbors can be detected
D.) Same autonomous network | | 1 |
| What command do you enter at the keyboard to begin a user mode
session?
A.) Type 'CTRL-P'
B.) Type 'login'
C.) Just press .
D.) Type 'enable'
E.) Press 'Shift + Ctrl + 6' at the same time. | | 1 |
| Identify the purpose of the following command 'ip route
192.168.100.0 255.255.255.0 10.1.0.1'
A.) Enabling a dynamic routing protocol
B.) Creating a static route to the 10.1.0.0 network
C.) Teaches the router about the distant network
192.168.100.0 and how
it can be reached via 10.1.0.1
D.) Assigning the IP address 192.168.100.0 to an interface | | 1 |
| What are four functions/characteristics of the network layer
of the OSI model? (Choose four)
A. It uses a two-part address
B. It maintains routing tables
C. It uses broadcast addresses
D. It establishes network addresses
E. It provides access to the LAN media
F. It provides media independence for upper layers
G. It provides path selection for Internetwork communication | | 1 |
| Identify the 2 types of access-list filters that control SAP
traffic?
A.) Novell-ether
B.) Arpa
C.) Input-sap-filter
D.) Round-robin
E.) Output-sap-filter | | 1 |
| You have powered on a new router and you want to create an
initial configuration. Which mode should you use?
A. copy mode
B. user mode
C. setup mode
D. startup mode | Enrich | 3 |
| Which of the following protocols are used for logical network
addressing?
A.) IP
B.) TCP
C.) ARP
D.) ICMP
E.) RARP
F.) BootP | | 1 |
| Which Distance Vector characteristic can help to speed up
convergence?
A.) Triggered Updates.
B.) Split Horizon.
C.) Poison Reverse.
D.) Hold Down timers.
E.) Inverse ARP. | | 1 |
| What is the result of using a hierarchical addressing framework?
A. increased availability of addresses
B. decreased distance between routers
C. increased router memory requirements
D. no need to maintain routing information | | 1 |
| Identify the command that will display the RIP routes
entering and
leaving the router?
A.) Router(config)# debug ip rip
B.) Route# debug ip rip
C.) Router>debug ip rip
D.) Router# debug rip routes | | 1 |
| The following is partial output from a routing table,
identify the
2 numbers in the square brackets; '192.168.10.0 [100/1300]
via 10.1.0.1,
00:00:23, Ethernet1'
A.) 100 = metric, 1300 = administrative distance
B.) 100 = administrative distance, 1300 = hop count
C.) 100 = administrative distance, 1300 = metric
D.) 100 = hop count, 1300 = metric | | 1 |
| |
| For more CCNA Interview Questions Click Here |
Site Map
