| Other CCNA Interview Questions |
| |
| Question | Asked @ | Answers |
| |
| Although Cisco IOS 11.2 and later can auto-detect the LMI
type in
Frame Relay, which command will force the LMI type to q933a?
A.) frame-relay lmi-type q933a
B.) encapsulation frame-relay q933a
C.) don't need to, it is the default
D.) encapsulation q933a
E.) encapsulation frame-relay type=q933a | | 1 |
| As system administrator, you type "debug ipx sap" and
receive the following lines as part of the IOS response:
type 0x4, "HELLO2", 199.0002.0003.0006 (451), 2 hops
type 0x4, "HELLO1", 199.0002.0003.0008 (451), 2 hops
What does "0x4" signify?
A. That is a Get Nearest Server response.
B. That it is a General query.
C. That it is a General response.
D. That it is a Get Nearest Server request. | | 1 |
| In regards to TCP/IP, which class of address allows for the
fewest
valid
Internet hosts?
A.) D
B.) E
C.) Classes are not used in TCP/IP.
D.) B
E.) C
F.) A | | 1 |
| Which of the following can reply to a Novell Get Nearest
Server (GNS)
request?
A.) Local Novell server
B.) Remote Novell Printer
C.) Cisco router
D.) Novell client | | 1 |
| 1. What is an advantage to LAN segmentation?
A. Provides multiprotocol support
B. Decreases security
C. Decreases broadcasts
D. Increases broadcasts
| | 2 |
| Choose three reasons why the networking industry uses a layered
model:
A.) It facilitates systematic troubleshooting
B.) It allows changes in one layer to occur without changing
other layers
C.) It allows changes to occur in all layers when changing
one protocol
D.) It clarifies how to do it rather than what general
function to be done
E.) It clarifies what general function is to be done rather
than how to do
it | | 1 |
| What is the syntax to use to configure the port on a
Catalyst 5000
switch?
A.) slot port/type
B.) type slot/port
C.) port slot/type
D.) port type/slot | | 2 |
| The Internet Control Message Protocol occurs at what layer
of the
seven layer model?
A.) Physical
B.) Transport
C.) Session
D.) Datalink
E.) Presentation
F.) Network | | 2 |
| what is routing and routed protocol ? | | 7 |
| The ICMP (referred to in PFC 1700) is implemented by all
TCP/IP hosts
A. true
B. false | | 1 |
| Which two describe frame tagging?
A.) Examines particular info about each frame
B.) A unique ID placed in the header of each frame as it
traverses the
switch fabric
C.) A user- assigned ID defined to each frame
D.) The building of filter tables | | 1 |
| raid can be used in?
1 NT
2 Netware
3 all of above
mine answer -NT | | 2 |
| On an ISDN BRI interface, the control channel is the 'D'
channel.
What is
the rate of this channel?
A.) 64 Kbps
B.) 1.544 Mbps
C.) 128 Kbps
D.) 2.048 Mbps
E.) 16 Kbps | | 2 |
| How does the cut-through switching technique work?
A.) By using broadcast address as source addresses
B.) The switch waits only for the header to be received
before it checks
the destination address and starts forwarding the packets
C.) The LAN switch copies the entire frame into its onboard
buffers and
then looks up the destination address in its forwarding, or
switching,
table and determines the outgoing interface
D.) By using a Class I repeater in a collision domain | | 1 |
| Which two statements are true? (Choose two)
A. Ethernet 802.3 utilizes a half duplex method for data
transfer
B. In a 100 MBS point to point connection a full duplex
connection can provide 400 Mbs of data transfer
C. Ethernet switches can use the full duplex mode to connect
multiple nodes on a single pod of a switch
D. Full duplex Ethernet takes advantage of UTP using one
pair for transmission and the other pair for reception | | 1 |
| HOW MPLS IS DIFFERENT FROM OSPF? WHY NOW A DAYS MPLS IS
PREFERED OVER ANY NETWORK PROTOCOL? | Bank-Of-India | 1 |
| Identify the command to configure ALL the default VTY ports?
A.) Router(config)# line vty 0 4
B.) Router# line vty 0 4
C.) Router(config)# line vty
D.) Router(config)# line vty 0 | Accel | 2 |
| You are logged into a router, what command would
show you the IP addresses of routers connected to you?
A. show cdp neighbors detail
B. show run
C. show neighbors
D. show cdp | | 2 |
| Identify the 4 that are not LAN technologies?
A.) HDLC
B.) FDDI
C.) 802.5
D.) HSSI
E.) SDLC
F.) Frame Relay | AXA | 1 |
| Which protocol is used for booting diskless workstations?
A.) IP
B.) ARP
C.) RARP
D.) TCP
E.) SNMP | | 1 |
| |
| For more CCNA Interview Questions Click Here |
Did you received any Funny E-Mails from your Friends and like to share with rest of our friends? Yeah!! you can post that stuff 
Site Map
