| Other CCNA Interview Questions |
| |
| Question | Asked @ | Answers |
| |
| Which three are typical operational phases in a basic
connection oriented neloyord service? (Choose three)
A. call setup
B. data transfer
C. load balancing
D. call termination
E. call priortization
F. data segmentation
G. data link identification | | 1 |
| Which of the following will show an extended access list 150?
A.) sh access-list
B.) sh ip int
C.) sh ip access-list 150
D.) sh access-list 150 extended | | 1 |
| Of the following, which reason applies to dividing a large
network into two or more smaller networks?
Performance
Security
Address Management
All of the above
| | 1 |
| Identify 3 feature of access-lists?
A.) Implicit deny will deny any packets not matched
B.) Processed sequentially from bottom to top
C.) Processed sequentially from top to bottom
D.) If a packet is denied it would be tested against the
remaining
statements in the access-list
E.) Once a match is made the packet is either denied or
permitted
F.) Enabled on all interfaces by default | | 1 |
| On Cisco catalyst 5000 how would you set the second port on the
controller in the first slot to full duplex?
A.) Set port duplex 1/1 full
B.) Set port duplex 1/2 full
C.) Set port duplex 0/1 full
D.) Set port duplex 0/2 full | | 1 |
| Given the following static route command, 'ip route 3.3.3.0
255.255.255.0
4.4.4.4 125', which portion represents the administrative
distance?
A.) 3.3.3.0
B.) 255.255.255.0
C.) 4.4.4.4
D.) route
E.) 125 | | 2 |
| Identify the command to display the status of the Frame Relay
virtual circuit?
A.) Router# show frame-relay virtual-circuit
B.) Router(config)# show frame-relay pvc
C.) Router# show frame-relay pvc
D.) Router# show virtual | | 1 |
| What does the Frame Relay switch use to distinguish between
each PVC connection?
A. data-link connection identifiers (DLCIs)
B. BECNs
C. FECNs
D. the Local Management Interface (LMI) | | 2 |
| Which of the following will apply IPX sap access list 1010 for
incoming traffic, assume you are at the interface configuration?
A.) ipx input-sap-filter 1010 in
B.) ipx input-sap-filter 1010
C.) ipx access-group 1010 in
D.) ipx access-list 1010 in | | 1 |
| What is the maximum hop count for Link-State protocols?
A.) 15
B.) there is no hop count limit
C.) 256
D.) 16 | | 1 |
| Which NetWare protocol works on layer 3--network layer--of
the OSI model?
A. IPX
B. NCP
C. SPX
D. NetBIOS | | 1 |
| What is a characteristic of Store and Forward switches?
A.) They work at wire speed.
B.) They are the same as Cut-Through switching in 'prune' mode.
C.) They forward based on transport layer info.
D.) They forward the frame before it is completely read.
E.) They increase latency. | | 1 |
| Identify the protocol to test connectivity without
configuring any
layer 3 protocols?
A.) TCP
B.) Ping
C.) IP
D.) CDP
E.) Telnet | | 1 |
| How to see the running-config & startup-config infor from
global configuration mode.
As we know, from priviledge mode we cn see it by executing
command. i.e.
Router#show running-config
and
Router#show startup-config
Now wat is the coommands use in global configuration mode o
see those info.
Router(Config)# ??????
| Juniper-Networks | 3 |
| Which statement is true regarding half duplex?
A.) Only works in a point-to-point configuration
B.) Allows for transmitting and receiving but not a the same
time
C.) Allow for transmitting and receiving of data simultaneously
D.) Doubles the bandwidth | | 1 |
| Novell NetWare has an Ethernet frame type called
Ethernet_II. What
is the matching Cisco command line keyword for this
encapsulation method?
A.) dix
B.) sap
C.) arpa
D.) gns
E.) snap
F.) novell-ether | | 1 |
| You are conferring a Frame Relay router with subinterfaces
on interface Serial 0 Which subinterfaces numbers could you
use for this configuration?
A. 1 and 2
B. 0 2 and 0 3
C. 1 0 and 1 1
D. 0 1 a and 0 1 | | 1 |
| What IP command would you use to test the entire IP stack?
A.) Stack-test
B.) Arp
C.) Telnet
D.) Ping
E.) Trace | | 1 |
| what is the difference between client mode and server mode of
vtp and what is the diffrence betwwen tarnsparent mode and
server mode | IBM | 4 |
| 10. Which STP state populates the MAC address table but
doesn't forward data frames?
A. Blocking
B. Listening
C. Learning
D. Forwarding
| Cisco | 3 |
| |
| For more CCNA Interview Questions Click Here |
To Refer this Site to Your Friends 
Site Map
