| Other CCNA Interview Questions |
| |
| Question | Asked @ | Answers |
| |
| How ICMP is used in ping and traceroute facilities | | 3 |
| What is VLSM? Why we Create? When we Create? Implement VLSM
with example? | | 4 |
| Which OSI layer supports the communication component of an
application?
A.) Data-Link
B.) Physical
C.) Session
D.) Presentation
E.) Application
F.) Transport | | 1 |
| What is the function of Layer 2 Device? | | 3 |
| Identify the command to configure the configuration-register?
A.) Router# config-register 0x2102
B.) Router(config)# config-register 0x2102
C.) Router(config-reg)# 0x2102
D.) Router> config-register 0x2102 | | 1 |
| Identify the command to configure the router to boot from an IOS
located on a TFTP server?
A.) boot system tftp IOS.exe 172.16.5.1
B.) boot system tftp 172.16.5.1 IOS.exe
C.) boot system flash tftp 172.16.5.1
D.) boot system IOS.exe 172.16.5.1 | | 1 |
| What is the UDP datagram format?
A. Source Port - 16 bits, Destination Port - 16 bits, Length
- 16 Bits, Checksum - 16 bits, Data
B. Destination Port - 16 bits, Source Port - 16 bits, Length
- 16 Bits, Checksum - 16 bits, Data
C. Source Port - 16 bits, Destination Port - 16 bits,
Checksum - 16 Bits, Length - 16 bits, Data
D. Source Port - 8 bits, Destination Port - 8 bits, Length -8
Bits, Checksum - 8 bits, Data | | 1 |
| 'Show cdp neighbors detail' show the following 3 pieces of
information?
A.) Hardware platform
B.) Software version
C.) Same as 'show version' command
D.) Up to 1 address for each protocol
E.) Non-direct connected routers | | 2 |
| Which of the following can reply to a Novell Get Nearest Server
(GNS) request?
A.) Local Novell server
B.) Remote Novell Printer
C.) Cisco router
D.) Novell client | | 1 |
| Using the TCP/IP protocol suite a message is sent from host
A to a destination IP address on the same LAN. How does
host A determine the destination of MAC address?
A. It uses a proxy APP
B. It uses APP requests
C. It uses RARP requests
D. It uses a router lookup table | | 1 |
| What is Cisco's default encapsulation method on serial
interfaces?
A.) ANSI
B.) Cisco
C.) Q933a
D.) HDLC | | 1 |
| Identify 2 reasons for disabling CDP?
A.) If the router is not configured for RIP
B.) Save bandwidth by eliminating overhead
C.) If the router is configured for Appletalk
D.) When connected to a non-Cisco router | | 1 |
| What is true when creating static route?
A.) The mask parameter is optional
B.) The administrative distance is required
C.) The gateway parameter is required
D.) The administrative distance is optional | | 1 |
| Which OSI layer establishes, maintains and terminates sessions
between
applications?
A.) Application
B.) Physical
C.) Data-Link
D.) Presentation
E.) Network
F.) Session | | 1 |
| What is the routing algorithm used by RIP and IGRP?
A.) OSPF
B.) Link-state
C.) Dynamic
D.) Distance Vector | Cisco | 2 |
| With distance vector routing protocols, it is never useful
to send
the same routing update packet back out the same interface
that it was
learned. This concept is called what?
A.) Holddown timers
B.) Poison Reverse
C.) Count to infinity
D.) Split Horizon
E.) Link State | | 2 |
| If you are running Token Ring with Novell IPX routing, which
encapsulation
should you use?
A.) SAP
B.) SNAP
C.) 802.5
D.) 802.2 | | 1 |
| Which command will display the IPX routing table?
A.) show routes
B.) show routes ipx
C.) show routes protocol=ipx
D.) show ipx
E.) show ipx route | | 1 |
| Identify 3 characteristics regarding IP access-lists?
A.) Can be configured as a standard access-list
B.) Can be run from another router running IP
C.) Can be configured as a named access-list
D.) Are the same as IPX access-lists
E.) Can be configured as an extended access-list | | 1 |
| Identify the command to display the status of the Frame Relay
virtual circuit?
A.) Router# show frame-relay virtual-circuit
B.) Router(config)# show frame-relay pvc
C.) Router# show frame-relay pvc
D.) Router# show virtual | | 1 |
| |
| For more CCNA Interview Questions Click Here |
along with your userid / name. ThanQ
Site Map
