| Other CCNA Interview Questions |
| |
| Question | Asked @ | Answers |
| |
| What does the IPX maximum-path command do?
A.) Allows you to disable the TTL on an IPX packet
B.) This parameter is only used in NLSP routing
C.) Sets the maximum metric that can appear in the routing table
D.) Configures round robin load sharing over multiple equal
metric paths
(parallel paths) | | 1 |
| Identify the command to display the status of the Frame Relay
virtual circuit?
A.) Router# show frame-relay virtual-circuit
B.) Router(config)# show frame-relay pvc
C.) Router# show frame-relay pvc
D.) Router# show virtual | | 1 |
| You want a message to be displayed every time someone tries
to log
on to the router. Which command is required to accomplish
this task?
A.) motd#(message)#
B.) banner motd(message)
C.) banner motd#(message)#
D.) banner motd*(message)
E.) banner login#(message)# | | 1 |
| Which statements are true regarding half duplex?
A.) Only works in a point-to-point configuration
B.) Allows for transmitting and receiving but not at the
same time
C.) Allow for transmitting and receiving of data simultaneously
D.) Doubles the bandwidth | | 1 |
| Identify 3 characteristics of a connection oriented protocol?
A.) Path determination
B.) Flow control
C.) Acknowledgements
D.) Uses hop count as metric
E.) 3 step handshake | | 2 |
| Identify the command that displays ethernet0/1 interface status?
A.) show interface ethernet0/1
B.) show interface ethernet e0/1
C.) show interface ethernet0.1
D.) show ethernet0/1 | | 3 |
| what is route aggregation | | 2 |
| What is a characteristic of Store and Forward switches?
A.) They forward the frame before it is completely read.
B.) They work at wire speed.
C.) They are the same a Cut-Through switching.
D.) They read the entire frame and check CRC before forwarding.
E.) They decrease latency. | | 1 |
| What must be true for two Routers running IGRP to communicate
their routes?
A.) Same autonomous system number
B.) Connected using Ethernet only
C.) Use composite metric
D)Configured for PPP | Allied-Group | 1 |
| What is the default encapsulation of Netware 3.12?
A.) Ethernet_II
B.) 802.5
C.) 802.2
D.) 802.3 | | 2 |
| Which type of LAN segmentation device enables high speed
data exchange?
A. hub
B. bridge
C. switch
D. repeater | TCS | 2 |
| For IPX, what is the DEFAULT Cisco Encapsulation on an Ethernet
interface?
A.) novell-ether
B.) gns
C.) snap
D.) arpa
E.) sap
F.) dix | | 1 |
| what is the purpose of multicast packets? | | 1 |
| Identify 3 LAN technologies?
A.) FDDI
B.) HDLC
C.) HSSI
D.) X.25
E.) 802.3
F.) 802.5 | | 1 |
| The -- terminal no editing -- command will perform what
function?
A.) Edit the contents of NVRAM
B.) Allows access to the terminal port
C.) Stops the advanced editing feature
D.) Enable password functions | | 1 |
| Which of the following is a characteristic of a switch, but
not of a
router?
A.) Switches forward packets based on the IPX or IP address
in the frame
B.) Switches forward packets based on the IP address in the
frame
C.) Switches forward packets based on the MAC address in the
frame
D.) Switches forward packets based only on the IP address in
the packet | | 1 |
| A network is vow congested currently all the devices are
connected through a hub. Which would best decrease
congestion on this network?
A. add a second hub
B. replace the hub with a router
C. replace the hub with a switch
D. replace the hub with a repeater | | 1 |
| Which can be true regarding VLANs?
A.) They are created by location
B.) They are created by function
C.) They are created by department
D.) They are created by group | | 1 |
| Which two describe frame tagging?
A.) Examines particular info about each frame
B.) A unique ID placed in the header of each frame as it
traverses the
switch fabric
C.) A user- assigned ID defined to each frame
D.) The building of filter tables | | 2 |
| What does the term Base refer to in 100BaseT
A. cabling type
B. singnal type
C. 100 mode type
D. spectrum used
E. speed category | | 2 |
| |
| For more CCNA Interview Questions Click Here |