Which statement is true regarding half duplex? A.) Only works in a point

Advertise your Business Here

Refer this Site

Login | Sign Up


	To Refer this Site to Your Friends Click Here

Categories >> Certifications >> Cisco Certifications >> CCNA

CCNA Interview Questions

CCDA Interview Questions

Question

Which statement is true regarding half duplex?

A.) Only works in a point-to-point configuration

B.) Allows for transmitting and receiving but not a the same
time

C.) Allow for transmitting and receiving of data simultaneously

D.) Doubles the bandwidth

Question Submitted By :: Guest

I also faced this Question!!

Rank

Answer Posted By

Re: Which statement is true regarding half duplex? A.) Only works in a point-to-point configuration B.) Allows for transmitting and receiving but not a the same time C.) Allow for transmitting and receiving of data simultaneously D.) Doubles the bandwidth

Answer
# 1

Answer: B

Half duplex is analogous to a single a lane bridge, it can
handle

traffic in both directions but no at the same time.

Is This Answer Correct ?

1 Yes

0 No

Guest

Question	Asked @	Answers
Other CCNA Interview Questions


Identify 3 Fast Ethernet technologies? A.) 100 Base FastEther B.) 100 Base FX C.) 100 Base T4 D.) 100 Base TX		1
Identify the command that configures the bandwidth to 56K? A.) Router(config-if)# bandwidth 56000 B.) Router(config-if)# bandwidth 56k C.) Router(config)# bandwidth 56 D.) Router(config-if)# bandwidth 56		1
Identify the 2 commands the saves the running-config to NVRAM? A.) write memory B.) copy running-config startup-config C.) write network D.) write backup		1
What is the difference between TCP and UDP? A.) TCP is connection-oriented; UDP uses acknowledgements only B.) TCP is connection-oriented; UDP is connectionless C.) Both TCP and UDP are connection-oriented, but only TCP uses windowing D.) TCP and UDP both have sequencing, but UDP is connectionless		4
Which protocol resolves an IP address to a MAC address? A.) DHCP B.) RARP C.) ARP D.) NBP E.) DNS		3
Hi Guys i hv one confusion. Need u peoples help. In EIGRP, maximum hop count is up to 255. By default only 100. Now question is - a) Suppose i hv a network consist of 115 routers & EIGRP routing protocol is configured. By default hop count is 100, so is there any manual configuration necessary for hop count ya router will automatically detect the hop count & will update the hop count accordingly..????? b) In EIGRP, Bandwidth & Delay is used to calculate metric. For this Metric weight is set to K1(Bandwidth)=1, K2(Delay)=0, K3(Reliability)=1, K4(Load)=0, K5(MTU)=0 Now i want, Bandwidth & Load is used to calculate metric. For that wat i hv to configure & wat wub the metric weights. Cud anyone explain it plzzzz..!!!!		5
What is the command to manually enter a static route? A.) IP route network B.) IP route C.) IP route < destination network> D.) IP route		1
Which ISDN protocol prefix specifies switching and signalling? A.) I B.) E C.) Q D.) S		1
how to troubleshoot when protocols is down and link is not getting up	HCL	5
What is the protocol and what is the purpose of the following address? 238 255 255 255 A. IPX a SAP broadcast B. IP a multicast group C. IP a reserved address D. IP a directed broadcast E. IPX a flooded broadcast		2
what is farme realy.and on which layer it work		1
how many pass word you can configure on cisco 2500 router	HCL	2
On Cisco catalyst 5000 how would you set the second port on the controller in the first slot to full duplex? A.) Set port duplex 1/1 full B.) Set port duplex 1/2 full C.) Set port duplex 0/1 full D.) Set port duplex 0/2 full		1
Which protocol is used for booting diskless workstations? A.) IP B.) ARP C.) RARP D.) TCP E.) SNMP		1
hi friend i hav difficulty n need to solve it...v need to implement a new raw switch in company as to increase the no of staff...snc raw switch by default is in server mode,i wanna know 1.how to make a switch in client mode...2.how to configure switch i mean to sy how to connect all switches to network.		1
Which OSI layer performs code conversion, code formatting and encryption? A.) Physical B.) Data-Link C.) Application D.) Transport E.) Presentation F.) Network		1
How would you set the clock rate to 64K, on interface serial 0, from the interface configuration mode? A.) clock rate 64000 B.) bandwidth 64 C.) clock 64 D.) rate 64 E.) clock rate 64k F.) clock rate 64		1
Which of the following is not a characteristic of link-state routing protocols? ❍ A. VLSM support ❍ B. Route summarization at any bit level ❍ C. Full routing updates at regular intervals ❍ D. Discontiguous network support		1
intial information of packey occur on which layer application sessions physical mine answer physical		1
Identify the switching method that examines the destination MAC address as the frame is being received then begins forwarding the frame prior to receiving the entire frame? A.) Fragment-free B.) Store and Forward C.) Cut-through D.) Fast forward		1

For more CCNA Interview Questions Click Here


Copyright Policy \| Terms of Service \| Help \| Site Map 1 \| Articles \| Site Map \| Site Map \| Contact Us \|

Copyright © 2007 ALLInterview.com. All Rights Reserved.

ALLInterview.com :: Forum9.com :: KalAajKal.com