| Other CCNA Interview Questions |
| |
| Question | Asked @ | Answers |
| |
| Cisco routers use wildcard masking to identify how to check or
ignore corresponding IP address bits. What does setting a
wildcard mask
bit to 0 cause the router to do?
A. It tells the router to check the corresponding bit value.
B. It tells the router to ignore the corresponding bit value.
C. It tells the router to check its alternate routing list.
D. It tells the router to use its primary routing list. | | 1 |
| In regards to the ISDN BRI standard, which channel is used for
control?
A.) B
B.) D
C.) E
D.) I
E.) Q | | 2 |
| Identify the 2 commands that will display the status and
information about interface E0 only?
A.) show interface ethernet E0
B.) show interface E0
C.) show E0
D.) show int E0
E.) show interface | | 1 |
| Which three protocols are correctly matched to their
transport layer functions? (Choose three)
A. route selection IP
B. sliding window UDP
C. well known pods IP
D. route validation ICMP
E. connection oriented TCP
F. three-way handshake TCP
G. no sequence and acknowledgement UDP | | 1 |
| How many total hosts are possible with a Class C address and
a subnet mask of 255.255.255.252?
A. 4
B. 30
C. 60
D. 62
E. 112
F. 124 | | 6 |
| A user device that connects to a DCE must be which of the
following?
A.) DTE
B.) CPE
C.) Demarc
D.) DCE
E.) CO | | 1 |
| Which command displays the IPX SAP table?
A.) show ipx sap
B.) show sap
C.) show ipx interface
D.) show ipx servers
E.) show ipx | | 1 |
| 1 what is the number of telnet session in the cisco router
a 1
b 2
c 3
d 4
e 5 | | 3 |
| Which IP Address Class is INCORRECTLY paired with its range
of network numbers?
A. Class A addresses include 192.0.0.0 through 223.255.255.0
B. Class A addresses include 1.0.0.0 through 126.0.0.0
C. Class B addresses include 128.0.0.0 through 191.255.0.0
D. Class C addresses include 192.0.0.0 through 223.255.255.0
E. Class D addresses include 224.0.0.0 through 239.255.255.0 | | 3 |
| 3. What does a bridge use to segment a network?
A. IP Addresses
B. Broadcasts
C. Application data
D. Media Access Control addresses
| | 2 |
| When would you use ISDN?
A.) To connect LANs using POTS
B.) To support applications requiring voice, data, and video
C.) When you need a consistent and very high rate of data speed
D.) To connect to IBM mainframes | | 2 |
| Why would you use static routing instead of dynamic routing?
A.) When you want automatic updates of the routing tables
B.) All the time
C.) When you have very few routes and want to conserve bandwidth
D.) When you have a gateway of last resort | | 1 |
| For IPX, what is the DEFAULT Cisco Encapsulation on an Ethernet
interface?
A.) novell-ether
B.) gns
C.) snap
D.) arpa
E.) sap
F.) dix | | 1 |
| Which IP Address Class can have 64,000 subnets with 64,000
hosts per subnet?
A. Class B
B. Class A
C. Class C
D. Class D | | 2 |
| Which two of the following protocols are used at the
Transport layer?
A.) ARP
B.) UDP
C.) ICMP
D.) RARP
E.) TCP
F.) BootP | | 7 |
| Identify the command to configure the router to boot from an
alternate IOS located in flash?
A.) boot system flash IOS.exe
B.) boot system tftp IOS.exe 172.16.5.1
C.) boot system alternate IOS.exe
D.) boot system rom IOS.exe | | 1 |
| Which command enables directly connected network 199.55.72.0
to be used by RIP?
A. Router(config router)# rip 199.55.0.0
B. Router(config router)# rip 199.55.72.0
C. Router(config router)# network 199.55.0.0
D. Router(config router)# network 199.55.72.0 | | 1 |
| Identify the command to run 'setup'?
A.) Router(config)#setup
B.) Router?setup
C.) Router#setup
D.) Router>setup | Karrox | 1 |
| what is diffrence between circit switching and packet
switching | Volvo | 1 |
| Cisco's implementation of ISDN BRI has multi protocol support,
SNMP MIB support, and what other features?
A.) Call waiting
B.) Compression
C.) ADSL
D.) 1.544 Mbps
E.) Call screening
F.) Negative 'G' support | | 1 |
| |
| For more CCNA Interview Questions Click Here |
along with your userid / name. ThanQ
Site Map
